IJRIT International Journal of Research in Information Technology, Volume 3, Issue 6, June 2015, Pg.110-122

International Journal of Research in Information Technology (IJRIT) www.ijrit.com

ISSN 2001-5569

Wireless video transmission Evaluation using Lossless video compression and 8x8 MIMO-OFDM wireless transceiver Sabahat Nazneen M.Tech Scholar, Akshaya Institute of Technology, Tumkur, Karnataka, India

Abstract :During the recent years, digital high-definition televisions are widely used due to the terrestrial television broadcasting. In addition, ultra high definition television format such as 4K(3840x2160p) and 8K(7680x4320p) has been standardized. And On the other side, high-speed wireless transmission system using MIMO-OFDM including IEEE 802.11n and 802.11ac wireless LAN standards have become more popular. Using such high-speed transmission systems, it is expected that high-definition video sequences can be transmitted without any degradation or loss of quality. Therefore, trying to develop such high-quality and highspeed video transmission systems over a wireless media by combining lossless video compression algorithms and MIMO-OFDM wireless transmission technology considering both hardware implementation and wireless transmission conditions. In this project, we evaluate a configuration of lossless video transmission systems. Experimental result shows that video sequences can be transmitted over 22 db carrier to noise ratio (CNR) wireless channels with complete pixel restoration rate.

1. INTRODUCTION Recently, due to the spread of high-definition television with the start of digital terrestrial television broadcasting, high-definition and high-resolution images such as 1920×1080 are widely available in ordinary digital home appliances. Wireless video transmission is an important technology For consumer electronics, such as digital television(DTV),Mobile multimedia devices such as smart phones , mobile video terminals, and pad/tablet devices HDTV (High Definition Television) has become more popular because it has higher resolution than traditional television systems and with an aspect ratio of 16:9 influenced by widescreen cinema. The data rate of uncompressed HD video can be as high as 3Gbps (1080p60, RGB444 pixel format at 8 bits per pixel). In the future, the data rate is expected to rise with increase in resolution and color quality. Since HD video sources require such large data rates, it may seem reasonable to compress the video stream before transmitting. However, compression introduces delay, reduces video quality and increases complexity at the transmitter and receiver .And also, the video display have to support multiple codecs to maintain interoperability with the various transmitter. Furthermore, the HD connector interface for HD video sources and displays supports uncompressed HD transmission. In addition, higher resolution video standards such as 4K (3840×2160) and 8K (7680×4320) have also studied towards the further increase in image quality. However, current wireless video transmission systems including television broadcasting, which

Sabahat Nazneen, IJRIT-110

IJRIT International Journal of Research in Information Technology, Volume 3, Issue 6, June 2015, Pg.110-122

supports high definition video sequences, are using lossy compression encoding techniques such as MPEG-2 where the bitrate is around 10 Mbps to 50Mbps. Since lossy compression algorithms utilize the characteristics of human vision, they can significantly reduce the amount of data. Meanwhile, in recent years, wireless transmission systems using the MIMO-OFDM such as IEEE 802.11 series wireless LAN systems are widely used widely, and these performance has greatly improved. In the latest wireless LAN standard, IEEE 802.11ac[1], transmission rates of up to 6.93 Gbps have been standardized with the configuration of 8×8 MIMO and 160 MHz bandwidth

1.1

MOTIVATION OF THE PROJECT Motivated by above background, here am trying to enhance higher quality video transmission system over a

wireless standard system by the combination of lossless video compression algorithm and MIMO-OFDM wireless transmission system .By concentrating on efficient hardware implementation and error correction techniques to cope with transmission errors. In this project, we evaluate a configuration of lossless video transmission systems with MIMO-OFDM wireless transmission system based on IEEE 802.11n standard.

2. Overview of IEEE 802.11n And OFDM-MIMO 2.1 IEEE 802.11n standard IEEE 802.11n is an improvement of previous IEEE 802.11 standards such as a/b/g by adding multiple input multiple outputs (MIMO). IEEE 802.11n operates in 2.4GHz and 5GHz. When operating in 2.4GHz it is allowed by regulation to use 20MHz wide channels and 40 MHz-wide channels in 5GHz IEEE 802.11n apply four spatial streams at a channel bandwidth of 40MHz and the integrated MIMOOFDM, which can significantly increase the physical transmission rate a high-throughput mode of IEEE 802.11n transmitter is used in this system, whose transmitter structure is depicted in. There is one data stream, one encoding stream, four transmitter antennas and five receiver antennas in the system. At the transmitter side, the MSB and LSB will pass the convolutional encoder and interleaver respectively, in case the MSB and LSB will mix up in the interleaver part. Then they are aggregated according to the given modulation scheme to pass the constellation mapper. In the MIMO module. Most PHY layer losses are recovered by retransmission-based error control mechanisms in the Media Access Control (MAC) layer [1]. Multiple transmission retries at the MAC cause drops in application throughput. In addition, most WLAN base stations and adapters employ automatic PHY transmission rate selection schemes to cope with reduced signal-to-noise ratio, which again translates into bandwidth fluctuations. Other traffic flows sharing the same network resources may also cause throughput degradation. MAC quality-of-service enhancements standardized by 802.11e [1] support traffic prioritization and reservation of dedicated transmission opportunities. However, these cannot entirely prevent bandwidth decreases due to channel degradations, and have not been widely deployed in current AV streaming systems.

Sabahat Nazneen, IJRIT-111

IJRIT International Journal of Research in Information Technology, Volume 3, Issue 6, June 2015, Pg.110-122 Pg.

2.2 WLAN AUDIO-VIDEO (AV) TRANSMISSION SYSTEM studie transmission WLAN is the most widely used standard in digital TV and DVDs. In particular, it studies of high-definition (HD) video, which poses a challenging scenario because of its high bit-rate. rate. Display devices equipped with WLAN interfaces and video decoder form the client side of the system. The client also monitors network statistics and sends feedback messages. The main input parameters of the rate adaptation methods are bandwidth and delay estimates. The techniques ddeveloped for obtaining these parameters The system is designed to support streaming from live video sources, such as cable/satellite receivers, as well as stored content. In the case of liive sources, picture frames arrive at the media transrater at periodic intervals. This prevents the usage of video pre fetching methods that transmit the data at a rate higher than the actual video bitrate. Fig.2.1 depicts the target WLAN media streaming scenario. Compressed AV sources connected to a media server and a WLAN access point form the sender side of the system. The server acts as a gatew way that adjusts the bit-rate of the input bit stream .it utilize utilizes MPEG-2 encoded video. The main focus of this study is on selection of the transmission rate rather than the actual rate reduction method. The proposed technique can be used together with open or closed-loop translating or even with scalable video

fig 2.2 2.2WLAN audio-video transmission system 2.3 ORTHOGONAL FREQUENCY--DIVISION MULTIPLEXING OFDM stands for Orthogonal Frequency Division Multiplexing which is a frequency division multiplexing modulation scheme used as a digital multi carrier modulation used for encoding digital data on different carrier frequencies. More number of closely placed orthogonal sub carrier signals systems are used to carry out data on several parallel data stream .Each sub carrier system is modulated with a conventional modulation scheme such as Quadrature amplitude modulation or binary phase shift keying at a low symbol rate by maintaining total data similar to carrier modulation scheme in the same bandwidth. Hypothetically,This

is

a

specialized

frequency

modulation method, in addition constraints considered for the carrier signal is orthogonal to one another, meaning that cross talk or the interference between the sub channels is eliminated and inter carrier guard bands are not required. This greatly simplifies the propose at both the transmitter and the receiver side. OFDM in fast Fourier transforms may be used to simplify the design design. it convert signals back and forth between the time ti domain and frequency domain and exploit the fact that any waveform may be decayed iinto nto a series of simple signal. signal Fast Fourier transforms are numerical algorithms used by computers to perform DFT calculations. it also enable OFDM to make use of bandwidth.. In practice, the sub channels are allowed to partially overlap in the frequency.

Sabahat Nazneen, Nazneen IJRIT-112

IJRIT International Journal of Research in Information Technology, Volume 3, Issue 6, June 2015, Pg.110-122

2.4

MULTIPLE

INPUT,

MULTIPLE

OUTPUT-ORTHOGONAL

FREQUENCY

DIVISION

MULTIPLEXING (MIMO-OFDM) Greg Raleigh invented MIMO in 1996. MIMO stands for multiple input, multiple output technology, which is used to multiply capacity by transmitting different signals over multiple transmitting antennas, and as defined in previous section Orthogonal frequency division which divides a channel into a huge number of closely spaced sub channels to afford more reliable communications at very high speed. MIMO can be used with interfaces such as time division multiple access and code division multiple access MIMO-OFDM combination is most widely used and form base for most wireless local area network and broadband networks, because it achieves the greatest spectral capacity and delivers the highest efficiency and throughput. It forms a prevailing interface for 4G and 5G networks. MIMO is the first radio technology that treat multipath propagation as a phenomenon which is to be oppressed and it multiplies the effieciency of a radio link by transforming multiple signals over multiple located channels. This can be accompanied without the need of additional bandwidths.

3. VIDEO COMPRESSION METHODOLOGY 3.1 Video data transmission format The video transmission system should be capable of reproducing the original signal accurately at the receiving end with less loss of information .A sequence of video is represented as a collection of still images or frames with a fixed resolution elements, and these images or frames are displayed one after another at a regular intervals. A signal of video is created by the Camera is being scanned transversely and down exactly 312 1/2 times and is reproduced on the monitor screen. A next scan of 312 lines is exactly half a line downward and interlaced with the first scan to form a picture with 625 lines. This is known as a 2:1 interlaced picture scanning. Then combined 625 lines is considered to be as a bunch of video and made up of two interlaced field scan. The total voltage produced is around one volt from the bottom of pulse to the top . hence one volt peak voltage average is considered. The luminance element of the signal is between 0.3v to 1 v, therefore is 0.75v is maximum. This is known as a combined video signal because the synchronization and video information is combined into a single signal. In the case of a colored signal, more information has to be provided. The color information is super imposed on the video signal by means of a color sub carrier. A reference signal, known as the chromatic burst is added to the back after the horizontal synchronization pulse to detect the difference in phase. The number of frames displayed per second is called frame rate. Values 15 to 60 frames per second (fps) are generally used. In addition, each still image is treated as a color image using three color components namely red, green, blue.each of which is represented by 8 bit per pixel in general. The bit rate of uncompressed video data can be calculated by the following equation. Bitrate (bps) = Width × Height × 24 × Frame rate

(1)

Table I shows the well-known video standards and its uncompressed bit rates. It can be seen that the amount of uncompressed video data becomes very large especially when the image resolution is large. Therefore transmitting the raw data over wireless is impossible. To transmit video data over wireless channels, we consider to

Sabahat Nazneen, IJRIT-113

IJRIT International Journal of Research in Information Technology, Volume 3, Issue 6, June 2015, Pg.110-122

use the lossless compression technique to reduce the amount of data without degradation of video quality. TABLE I.

VIDEO STANDARDS AND BIT-RATE .

NAME

RESOLUTIO N

FRAM ERATE( fps)

BIT-RATE

DVD(480p)

720X480

60

497.7Mbps

720p

1280X720

60

1327.1Mbps

Full HD(1080p)

1920X1080

60

2986.0Mbps

4K

3840X2160

60

11.9Gbps

SHV(8K)

7680X4320

120

95.6Gbps

3.2 Encoding of video images Each wireless channel is capable of data rates of up to 4-Gbps therefore when all four are combined in this way, up to 16-Gbps of data throughput can be achieved. However interference was observed when there was a separation distance of less than one meter between neighboring connections Therefore, Uncompressed video data is too large to be transmitted over wireless channels as described above . However, redundancy in general video data is also large, so it is possible to reduce the amount of data significantly by various approaches. The compression approaches of video sequences can be roughly divided into three approaches: (1)

utilizes the characteristics of the human visual system,

(2)

utilizes the temporal correlation, and

(3)

utilizes the spatial correlation First approach utilizing human visual characteristics exploits that the human vision system is very sensitive

to low frequency components but not much sensitive to high frequency components. By using this fact, the amount of data can be reduced by decomposing image data into frequency components using spatial transformations such as discrete cosine transform (DCT), and decimating the high frequency components. This technique has been adopted by JPEG format widely used for photographic image compression, and by MPEG standards. However, the loss of information cannot be avoided in this method since it performs compression by decimating the high frequency components. Therefore this method is not suitable for lossless video transmission systems. The next approach utilizes the correlation in the temporal domain. This approach performs compression by using the information of several previous frames. In some cases, the following frames are also used. In the case of ordinary moving pictures, temporally adjacent frames are resemble. Therefore it is possible to reduce the amount

Sabahat Nazneen, IJRIT-114

IJRIT International Journal of Research in Information Technology, Volume 3, Issue 6, June 2015, Pg.110-122

of data by handling the difference between them. MPEG series utilizes this feature, whose technique is called motion

compensated inter-frame prediction, in addition to the aforementioned DCT. However, since some

previous frames must be stored completely in order to use this technique, the required memory size becomes quite large. Therefore we do not utilize this approach in this project considering the hardware cost. The third approach utilizes the spatial correlation, which is adopted in this project as the compression approach. This approach tries to utilize the characteristic that the values of the pixels located near each other have similarity. By taking the difference between adjacent pixels, the possibility that they have a small value near zero becomes high. By utilizing this small deviation of the probability distribution function, it is possible to reduce the amount of data by entropy coding in the subsequent stage. Compared to the first two approaches, this approach has an advantage that it can achieve

lossless

compression without any data losses. This approach can also reduce memory usage because it only uses the data of adjacent pixels, compared to the second approach. In the contrary to these advantages, the compression efficiency of this approach remains relatively very low.

OVERVIEW OF THE PROPOSED SYSTEM 4.1 The system overview The system overview considered in this project is shown in Fig. 4.1.It consists of transmitter and receiver part where once the system receives an input frame of RGB color space of video frame and this color space is converted from RGB to YUV form and this conversion is performed to enhance the compression efficiency and robustness. After that, each input frame is divided into blocks of different sizes to prevent the propagation of transmission errors. Next, image compression is performed based on different compression techniques for each block independently. then, Reed-Solomon encoding is applied as a countermeasure for transmission errors to detect and correct the error if any. Then each block is packetized and these packets are transmitted over wireless channels with 8×8 MIMO-OFDM modulation. and at the receiver end demodulation and decoding is done to get back the sequence without degradation or loss . Functional blocks shown in Fig.4.1 are roughly classified into three parts: •

image compression part,



error correction part ,and



wireless transceiver part.

The following section, describes an overview of each functional block.

Sabahat Nazneen, IJRIT-115

IJRIT International Journal of Research in Information Technology, Volume 3, Issue 6, June 2015, Pg.110-122

Fig 4.1.: System overview of a lossless video transmission system

4.2. MIMO-OFDM wireless transmitter and reciever part In this project, it uses an 8×8 MIMO-OFDM wireless transmission system is used based on IEEE 802.11ac standard. The system uses radio waves of 5 GHz frequency band, eight spatial streams, and 80 MHz bandwidth for each. In this IEEE 802.11ac standard, configurations of one to eight spatial streams and 20 MHz to 160 MHz bandwidth are defined. I n o r d e r to deal with the conditions of transmission channels, some parameter are considered by setting certain standard values, such as coding rate of the convolutional coding and sub-carrier modulation schemes such as BPSK ,QPSKQ,QAM etc are defined. TABLE II.

RELATION BETWEEN MCS AND BIT-RATE IN 8×8 MIMO 80 MHZ BANDWIDTH CONFIGURATION .

MCS

Modulation

Coding rate

Bit rate

0

BPSK

½

234 Mbps

1

QPSK

½

468 Mbps

2

QPSK

¾

702 Mbps

3

16-QAM

½

936 Mbps

4

16-QAM

¾

1404 Mbps

5

64-QAM

2/3

1872 Mbps

6

64-QAM

¾

2106 Mbps

7

64-QAM

5/6

2340 Mbps

8

256-QAM

¾

2808 Mbps

9

256-QAM

5/6

3120 Mbps

Sabahat Nazneen, IJRIT-116

IJRIT International Journal of Research in Information Technology, Volume 3, Issue 6, June 2015, Pg.110-122

4.3.Video compression part High-speed but low-power video compression which can be implemented by low hardware resources is required to the video compression part .The algorithm utilized in this project, is same as the existing method ,so we explain the algorithm briefly in following sections The algorithm used here performs compression by using the information of two pixels that are adjacent to the left and above of the target pixel and here spatial correlation is considered.

Block diagram of video compression algorithm. Golomb-Rice coding Golomb-Rice coding first converts an input value to ݊-bit binary code and then codes upper (݊-݇)-bit with unary codes while lower ݇ bits are left as they are.Unary coding outputs series of 1 whose number is same as of the input value and outputs 0 as a separator bit at the end. Adaptive binary coding : If ܲ1 ≤ ܲ ≤ ܲ2

where the target pixel value and two adjacent pixel values are

ܲ ,ܲ1 , and ܲ2 , respectively, we use a geometric based adaptive binary coding to code prediction error ‫ܧ‬, which is ܲ − ܲ1 or ܲ2 − ܲ . Color-space conversion In the proposed system, we utilize color-space conversion. Since variance of chrominance values is smaller than that of luminance, chrominance compo- nents can be compressed efficiently compared to the luminance component. When input is RGB, the input is converted to YUV before compression in order to improve compression ratio in the proposed system. RGB Color Space: The red, green, and blue (RGB) color space is widely used throughout computer graphics. Red, green, and blue are three primary additive colors (individual components are added together to form a desired color) and are represented by a three-dimensional, Cartesian coordinate system. The indicated diagonal of the cube, with equal amounts of each primary component, represents various gray levels. The RGB color space is the most prevailing choice for graphics because color displays use RGB to form the preferred color. hence, the preference of the color space simplify the construction of the complete system, since this color space has been approximately for a number of years.

Sabahat Nazneen, IJRIT-117

IJRIT International Journal of Research in Information Technology, Volume 3, Issue 6, June 2015, Pg.110-122

To support reversible color transformation from RGB to YUV, in the case of general YUV conversions such as that used in MPEG series or other systems, bit length of each pixel component in YUV color-space should be more than that in original RGB color-space. To solve this problem, reversible color transformation (RCT) is used in JPEG2000[6], which is one of image compression standards. In the case of 8- bit input for each RGB component, the original RGB pixel can be restored from 8-bit luminance and 9-bit chrominance component. RCT and inverse RCT are shown as follows Y=[R+2G+B/4] U=B-G V=R-G G=Y-[U+V/4] R=V+G B=U+G In order to convert RGB to YUV form we can also use the equation shown below Y= 0.299R+0.587G+0.114B U=0.493(B-Y) V=0.877(R-Y) In the proposed system, RCT is used for color-space conversion.

4.4 Transmission error concealment part In the previous sections, the video compression algorithm used in the proposed system is described. However, because of the use of information on adjacent pixels to restore the pixel data, there is a problem that the value of adjacent pixels is changed from its original value by transmission errors. In this case, the algorithm cannot restore any following pixels correctly. Therefore, we utilize a method to restore data using ReedSolomon error correcting code. In addition, we divide video frames into blocks to narrow the affected area.

Reed-Solomon error correcting code: Reed-Solomon code is one of the error detecting and correcting codes. Due to its high performance, ReedSolomon code is widely used from optical media storages, such as DVD and CD, to communication technologies such as digital terrestrial broadcasting . Reed-Solomon code treats multiple bits as a symbol and forms code-words with multiple symbols. Assuming that ܴ, and ‫ ܭ‬represent the number of bits, symbols, the original data symbols in one code-word, respectively, these numbers follow.ܰ − ‫ ܭ‬is the number of the redundant symbols generated by the ReedSolomon encoding. It can detect ܰ − ‫ ܭ‬pieces of symbol errors, and correct (ܰ − )/2 pieces of symbol errors. The generated ReedSolomon code is called ܴ(ܰ, ‫) ܭ‬.

Sabahat Nazneen, IJRIT-118

IJRIT International Journal of Research in Information Technology, Volume 3, Issue 6, June 2015, Pg.110-122 Pg.

Block division of video frames: When the transmission error that cannot be corrected by Reed-Solomon Reed code occurs, it is not possible to restore the original data, and is no longer a lossless transmission. However, H if the compression is performed for each frame, when an error occurs at a pixel in the frame, no subsequent data can be restored. To alleviate this problem, the compression is performed for each small block divided vided from input frame independently. Each block is processed, cessed, Reed-Solomon encoded, and transmitted as a different ferent packet. pac This block division also facilitates parallelization of the compression/decompression process

5. RESULT ANALYSIS AND PERFORMANC PERFORMANCE E VALUAT ION 5.1 compression efficiency ficiency Evaluation results In this chapter the results are evaluat aluated by the performance of the applied compression algorithm. Because As we already know that the compression algorithm does not have any time domain process, process like as inter-frame prediction, evaluation can be performed using video frames as still images as an input. Figure 7.1 shows input video which is divided into several frames and used in this evaluation to compare compression efficiency of OFDMOFDM MIMO system

Table III.. For without compression without RS Encoder and 8x8 MIMO SNR

Compression ratio

BER

PSNR

MSE

-5

100

0.0154

23.28

304.87

-4

100

0.0081

25.99

163.64

-3

100

0.00403

28.78

86.05

-2

100

0.00171

32.57

35.93

-1

100

0.00059

36.61

14.171

0

100

0.00017

44.53

2.28

5

100

0



0

Table IV IV. For with compression with RS Encoder and 8x8 MIMO

Sabahat Nazneen, Nazneen IJRIT-119

IJRIT International Journal of Research in Information Technology, Volume 3, Issue 6, June 2015, Pg.110-122

SNR

Compression ratio

BER

PSNR

MSE

-5

18.67

0

38.79

8.577

-4

18.67

0

38.79

8.577

-3

18.67

0

38.79

8.577

-2

18.67

0

38.79

8.577

-1

18.67

0

38.79

8.577

0

18.67

0

38.79

8.577

2

18.67

0

38.79

8.577

5

18.67

0

38.79

8.577

SNR

Without RS

With RS

10

0.3333

0.33

12

0.166

0.166

14

0.04166

0.031

16

0.010416

0.004

18

6.51042e-5

0

20

6.51042e-5

0

22

6.51042e-5

0

Table V. For with compression without RS Encoder and 8x8 MIMO Tables above show the compression ratio for each input still image of a video sequence using various SNR values. From these tables, it can be seen that the compression ratio of image for different combinations is differed .Since image

contains more fine textures such as a part of road,vehicle, it is considered that it makes the

correlations of adjacent pixels low and that it leads the bad compression ratio. It should be noted that the compression ratio varies depending on the spacial redundancy of the input data in the lossless compression algorithm. Since the output bit rate varies depending on the different frames or scenes, it is necessary to use some averaging process, such as buffering the output data. 5.2 wireless transmission Evaluation using 802.11n In this part, evaluated the video quality when there is a

transmission error. This

evaluation is

conducted using wireless transmission simulator. Transmitted video sequence is 1920×1080 resolution, 15 frames per second, and 1 second length (total 15 frames). Its uncompressed bit-rate is about 1.5 Gbps. The block size used in this evaluation is 302×302 for better balance of both packet overhead and memory usage.

Sabahat Nazneen, IJRIT-120

IJRIT International Journal of Research in Information Technology, Volume 3, Issue 6, June 2015, Pg.110-122

Conclusion and Future Work In the study of this project, investigated the anti-technology to transmission error required for, and lossless compression algorithm, and targeting wireless transmission of high definition video signal sequence with no loss of information and no quality degradation, over an 8×8 MIMO-OFDM wireless transmission system. From the evaluation results that are intended to be in the wireless transmission environment, we confirmed that the transmission without quality loss of high-definition video are possible in the condition of different SNR or more with BPSK modulation technique. In order to extend the condition of transmission without degradation and error free sequence is possible, we will ha ve to go for high end technologie s such as the compression algorithm with higher compression ratio, more effective error correcting methods, and retransmission control upon detecting a transmission error correcting it.

REFERENCE S [1]

Peter cherriman ,Thomas keller, “Orthogonal frequency-division multiplexing

Encoded Video over Highly Frequency-Selective Wireless systems for video technology, vol. 9, no. 5, [2]

Transmission of

H.263

Networks”, IEEE transactions on circuits and

august 1999.

M.Manohara, R. Mudumba “error correction scheme for uncompressed HD video over

wireless”,

in

Wireless Communications and Networking Conference, 2008, pp. 1939-1944. [3]

Van Wang, Danpu Liu, Mingliang Li ,“A survey on Hierarchical Modulation High-

Transmission Based on IEEE 802.11n”, Computer Modeling and

definition Video

Simulation, 2010. ICCMS '10. Second

International Conference . [4]

Chenwei Deng ,“Content-Based Image Compression for Arbitrary-Resolution Display

Devices”IEEE

transactions on multimedia, vol. 14, no. 4, august 2012. [5]

Kevin Gatimu, Taylor Johnson ,“Ultra-High Definition Wireless Video Transmission using

over 802.11n WLAN: Challenges and Performance Evaluation”, 12th International

H.264

Conference

on

Telecommunications - ConTEL 2013. [6]

Rohit Bodhe ,“ Design of simulink model for OFDM and comparison of FFT OFDM and

OFDM”, International Journal of Engineering Science and Technology

DWT-

(IJEST)ISSN : Vol. 4 No.05 May

2012. [7]

Eng Hwee Ong, Jarkko Kneckt, Olli Alanen, Zheng Chang, Toni Huovi- nen, and Timo Nihtila¨

802.11ac: Enhancements for very high throughput WLANs,” in Proc. International Indoor and Mobile Radio Communications, pp. [8]

Symposium

on

“IEEE Personal,

849–853, Sep. 2011.

ITU-T H.262, “Information technology — Generic coding of moving pictures and

associated

audio

information: Video,” 1994. [9]

ITU-T Recommendation T.87, “Information technology — Lossless and near- lossles compression

continuous-tone still images — Baseline,”1998.

Sabahat Nazneen, IJRIT-121

of

IJRIT International Journal of Research in Information Technology, Volume 3, Issue 6, June 2015, Pg.110-122

[ 1 0 ] P. G. Howard and J. S. Vitter, “Fast and efficient lossless image compression,” in Proc.Data Compression Conference, pp. 351–360,1993. [11]

Tsung-Han Tsai, Member, IEEE, and Yu-Hsuan Lee, “A 6.4 Gbit/s embedded compression codec for memory-efficient applications on advanced-HD specification,” IEEE Transactions on Circuits and Systems for Video Technology, Vol. 20, No. 10, pp. 1277– 1291, October 2010.

[12]

Athanassios Skodras, Charilaos Christopoulos, and Touradj Ebrahimi, “The JPEG 2000 Still Image Compression Standard,” IEEE Signal Processing Magazine, pp. 36–58, Sep.

2001.

[13]

IntoPIX, "Digital Cinema JPEG 2000 Encoder and decoders IP-Cores", 2011 Available

[14]

J. Halák, M. Krsek, S. Ubik, P. Žejdl, and F. Nevřela, "Real-time long- distance transfer

online. of

uncompressed 4K video for remote collaboration," Future Generation Computer Systems, vol. 27, pp. 886892, 2011. [15] D. Shirai, T. Kawano, T. Fujii, K. Kaneko, N. Ohta, S. Ono, et al., "Real time switching streaming transmission of uncompressed 4K motion pictures," Future Generation

and Computer

Systems, vol. 25, pp. 192-197, 2009. [16]

A. O. Ejeye and S. D. Walker, "Uncompressed quad-1080p wireless video streaming," Science and Electronic Engineering Conference (CEEC), 2012 4th, 2012,

in

Computer

pp. 13-16.

[17] T. K. Paul and T. Ogunfunmi, "Wireless LAN Comes of Age: Understanding the IEEE

802.11n

Amendment," Circuits and Systems Magazine, IEEE, vol. 8, pp. 28-54, 2008. [18]

C. T. Calafate, M. P. Malumbres, and P. Manzoni, "Performance of H.264 compressed video streams

over 802.11 b based MANETs," in Distributed Computing Systems Workshops, 2004. Proceedings. 24th International Conference on, 2004, pp. 776-781. [19]

K. Soroushian, S. Priyadarshi, and J. Villasenor "H. 264 Parameter Optimizations for

Internet

Distribution of High Quality Video”, in SMPTE Conferences,2008,pp1-15.

Sabahat Nazneen, IJRIT-122

Based

Wireless video transmission Evaluation using Lossless video ... - IJRIT

support streaming from live video sources, such as cable/satellite ..... Solomon code is widely used from optical media storages, such as DVD and CD, .... S. Priyadarshi, and J. Villasenor "H. 264 Parameter Optimizations for Internet Based.

312KB Sizes 5 Downloads 321 Views

Recommend Documents

Wireless video transmission Evaluation using Lossless video ... - IJRIT
open or closed-loop translating or even ... several parallel data stream . ..... the condition of transmission without degradation and error free sequence is possible ...

Video Conference System Using Raspberry Pi - IJRIT
the early 1970s as part of AT&T's development of Picture phone technology. With the ... (such as phone and Internet), by reducing the need to travel, which is often carried out by aero plane, to .... There is no arrangement for audio input in Raspber

Real-time Transmission of Layered MDC Video over Relay ... - IJRIT
MDC generates multiple descriptions of the same source data that can be ... In this paper, we propose a system for real-time video streaming to mobile users, via ...

Real-time Transmission of Layered MDC Video over Relay ... - IJRIT
To enable seamless and uninterrupted real time multimedia transmission to ..... End-to-end delay refers to the time taken for a packet to be transmitted across a ...

Digital Video Transmission over Wireless Channels 1 ...
4 Tools for Digital Video Transmission on Wireless Channels 4. 4.1 Tools on Encoder Side . ... H owever , we will mainly focus on diff erent characteristics.

Modeling of H.264 Video Transmission over MBMS
into RTP packet, and transmitted through the RTP/UDP/IP protocols. Although higher ... tested “News”, “Foreman”, and “Football” sequences in our simulations.

Network-Adaptive Video Coding and Transmission - (AMP) Lab ...
1. INTRODUCTION. The technology for delivering ubiquitous high bandwidth multimedia services, such as voice with video, will soon become a reality.

True Motion Vectors for Robust Video Transmission
In this way, no syntax is needed to support the recovery of missing data. .... pixels of the same moving object move in a consistent way, there should be a good degree of motion smoothness .... In an error-free condition, F(t + 1) depends on F(t).

pdf-1833\digital-video-transcoding-for-transmission-and-storage.pdf ...
There was a problem previewing this document. Retrying... Download ... or edit this item. pdf-1833\digital-video-transcoding-for-transmission-and-storage.pdf.

MULTI-VIDEO SUMMARIZATION BASED ON VIDEO-MMR
we propose a criterion to select the best combination of parameters for Video-MMR. ... Marginal Relevance can be used to construct multi-document summaries ... is meaningful to compare Video-MMR to human choice. In a video set, 6 videos ...

Scalable Video Summarization Using Skeleton ... - Semantic Scholar
the Internet. .... discrete Laplacian matrix in this connection is defined as: Lij = ⎧. ⎨. ⎩ di .... video stream Space Work 5 at a scale of 5 and a speed up factor of 5 ...

Scalable Video Summarization Using Skeleton ... - Semantic Scholar
a framework which is scalable during both the analysis and the generation stages of ... unsuitable for real-time social multimedia applications. Hence, an efficient ...

A Robust Video Watermark Embedding and Extraction ... - IJRIT
The performance of algorithm is tested using MATLAB software on video of “rhinos” and watermark image of ... divided into blocks of 8 X 8 and applies singular values decomposition technique on these blocks. ... In our proposed algorithm, Singular

A Robust Video Watermark Embedding and Extraction ... - IJRIT
more secure and highly robust against frame dropping & other manipulations. ... watermarks can be a logo or text on frames of videos either in all frames or in just a few ... If the extraction process needed the original data for the recovery of.

Video steganography
Jul 11, 2003 - ing, resampling, conversion from digital to analog and back again, etc. ...... 855-884. Pitas et al., “Applying Signatures on Digital Images,” IEEE.

Cheap Wireless 2.4Ghz 4 Channel Tv Audio Video Av Transmitter ...
Cheap Wireless 2.4Ghz 4 Channel Tv Audio Video Av T ... er And Receiver Free Shipping & Wholesale Price.pdf. Cheap Wireless 2.4Ghz 4 Channel Tv Audio ...

Opportunistic Network Coding for Video Streaming over Wireless
Jun 11, 2007 - coding to improve throughput in a wireless mesh network. .... together into a single packet, called the network code.1 The ...... services”, 2005.

Video Worksheet
... easy appeal to you? What are some of your favorites? 9. Geography – Are your choices of food related to where you live? 10. Healthy Lifestyle – Do you eat enough healthy foods? Do you read nutrition labels? ©Learning ZoneXpress • www.learn

Cheap Wifi Wireless 1080P HD 2MP 360 Degree Video Camera ...
Cheap Wifi Wireless 1080P HD 2MP 360 Degree Video ... anoramic Camcorder for iOS-Android Phone Black.pdf. Cheap Wifi Wireless 1080P HD 2MP 360 ...

Cheap Pat-530 5.8G Wireless Av Tv Audio Video Sender ...
Cheap Pat-530 5.8G Wireless Av Tv Audio Video Sender ... d Stb Dvr Brazil Free Shipping & Wholesale Price.pdf. Cheap Pat-530 5.8G Wireless Av Tv Audio ...

performance evaluation of mpeg-4 video over realistic ...
network emulator is based on a well-verified model described in [2]. ... AT&T Labs – Research, USA ... models derived from EDGE system level simulations [2].