Using a Current Sharing Controller with Non-Redundant Supplies Design Note 1036 Bob Smith Introduction The LTC®4370 is a 2-supply current sharing, diodeORing controller that uses MOSFETs to form ideal diodes. In this way, the LTC4370 can actively balance the output currents of two supplies, even those with unequal output voltages. For two unequal voltage input supplies, the forward voltage of the higher voltage supply diode is servoed to balance the shared load current. The maximum allowable voltage drop is programmed by a resistor at the RANGE pin of the LTC4370. A typical diode-OR system is a winner-take-all system where the highest voltage supply sources the entire load current. This one-supply-at-a-time scheme underutilizes the two supplies. The LTC4370’s current sharing diode-OR solution, on the other hand, reaps the benefits of sourcing and sharing current from both supplies: • Supply lifetimes are extended if each takes on half the load, spreading the supply heat and reducing thermal stresses on supply components. • Because the lower voltage supply is always operational, there is no surprise when transitioning to a backup supply that may have already silently failed—a possibility in a simple diode-OR system. • The recovery dynamics on supply failure are smoother and faster, since the supply changes are on the order of less and more, not off and on. • A DC/DC converter formed by two supplies running at half capacity has better overall conversion efficiency than a single supply running near full capacity.

11/15/1036

Normally the LTC4370 is used to current share the outputs of two supplies, either of which is capable of providing the entire load current when its mate drops below the sharing voltage threshold set by the RANGE pin of the LTC4370. The current sharing function may also be used to provide the total load current by two lower current supplies with a combined current equal to, or in excess of that required by the load. A problem remains, however, that in normal operation, the LTC4370 allows the higher voltage supply to source all of the load current. Since, in this case, the remaining supply is incapable of providing the full current, it is necessary to prevent such operation. This design note describes a solution that disables the downstream load when this situation occurs. Principal of Operation In normal operation, the LTC4370 monitors the current of both supplies. Normally with a perfect diode, the supply with the higher voltage would source all of the current to the load. The LTC4370 prevents this by linearly controlling the MOSFET of the higher voltage supply to provide current equal to that of the lower voltage supply. The maximum voltage difference allowed is determined by the resistor between the RANGE pin and ground. When the input supply voltage difference rises beyond the programmed range, the LTC4370 disables the current sharing function. There are two alarm outputs, L, LT, LTC, LTM, Linear Technology, the Linear logo and Over-The-Top are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners.

each monitoring the control voltage at the gate of each MOSFET. In normal operation, when either MOSFET is turned off (indicating a voltage difference beyond the programmed range) its associated FETON signal is set to a logic low. In theory it seems that if these signals were passed through a logic AND function, they could be used to control the downstream load, disabling it when a MOSFET is turned off (indicating the loss of current sharing). These signals, however, both revert to logic low when zero current is passing through the MOSFET. In this situation, with the downstream load disabled and drawing no current, the system would remain in this state indefinitely. The solution described here senses input voltage differences and disables the downstream load when a defined voltage difference between the supplies is detected. This voltage difference is programmed to be below the maximum voltage threshold of the LTC4370. If an out of balance condition is detected, the downstream power supply is disabled. To prevent an oscillatory condition, the circuit enters hiccup mode, where the supply is cycled on for 200ms every 3.2 seconds. The block diagram is shown in Figure 1. As shown in the block diagram, two comparators are used to sense when the absolute value of the difference

between power supply inputs VINA and VINB is beyond that allowed for proper current sharing. When this happens, the output of the negative true OR gate is a logic high, enabling the hiccup circuit. Normally, the output of the hiccup circuit is a logic high, enabling the downstream load. When the out of range fault condition is detected, the hiccup circuit is activated, causing a logic low to disable the downstream load. The hiccup circuit monitors the voltage differential during the 200ms on period and is disabled when the fault condition is cleared. Circuit Description Figure 2 shows the complete solution. In Figure 2, U2 and U3 are LT1716 Over-The-Top ® voltage comparators used to detect voltage differences between VINA and VINB. Threshold offset voltage to the comparators is provided by current sink transistors Q5 and Q6 in combination with R8 and R9. Current at the collectors of Q5 and Q6 is stabilized at 100µA by transistors Q1, Q2, Q3, and U6, an LT6650 voltage reference. In this case, R8 and R9 are set to 3.01k, resulting in an offset of 300mV. These resistor values can be changed to provide a different offset to match that of the LTC4370.

VINA

LTC4370

VINB

– –

VTH

VTH

+

– +

+

– +

A > (B + TH)

FEED

TO LOAD

DIODE-OR CURRENT SHARING CONTROLLER (ON 200ms, OFF 3.2s)

HICCUP CIRCUIT

ENABLE

B > (A + TH)

Figure 1. Block Diagram of Current Summing Circuitry

TO LOAD

dn1036 F01

VINB

EN2

GND

EN1

2

IN

1 U6 FB LT6650 5 OUT GND

4

C5 1µF R10 10M

C6 1µF

Q3

2N2907(2)

2N2907

Q1

R6 1k

R11 40.2k

Q4

Q2

R7 1k

C1 0.1µF

R12 40.2k

Q5

R8 3.01k

R9 3.01k

13

5 1

3

4

U3 LT1716

3

4

U2 LT1716

C7 0.47µF

2

5

2

OUT2

FETON2

FETON1

R14 499k

5

4

2

1

10

9

C8 0.1µF

5

3

7

8

9 OFF1

D

C

A

6

3

8 13

12

U4 74HC132

2

7

10

B

C4 0.18µF

OFF2

R2 4.7k

M2 SUM85N03-06P

COMP GATE2

Figure 2

1

4

6 C3 0.039µF

VIN2

12

M1 SUM85N03-06P GATE1 10 OUT1

U1 LTC4370CDE

VIN1

CPO2

EN2

RANGE

EP

GND

VCC

EN1

R13 40.2k 2N2222X3

Q6

R1 30.1k 1

2

17

15

14

16

CPO1

11

C2 0.039µF

+ –

VINA

+ –

9

CP PE

CEP

CET

11

R3 4.7k

3

4 P1

5 P2

13

Q1

12

Q2

U5 74HC163

14

Q0

P0

C9 0.1µF

R5 2mΩ 1%

R4 2mΩ 1%

6

MR

TC

11

8

dn1036 F02

1

15

16 VCC

Q3 GND

P3

VIN FAULT

ENABLE (TO LOAD)

OUTPUT (TO LOAD)

GND

When either comparator U2 or U3 reaches the threshold determined by the offset, their output becomes logic low, enabling the hiccup circuit. U4 is a 74HC132 quad CMOS NAND gate with hysteresis on each input. U5 is a 74HC163 4-bit programmable CMOS counter. The output of U4A is logic low when VINA and VINB is within the threshold determined by R8 and R9. When VINA and VINB is beyond this threshold, the corresponding comparator output becomes logic low, causing the output of U4A to become a logic high. A logic high output of U4A is inverted by U4B, producing a logic low at one input of NOR gate U4C. The resulting logic high output of U4C causes counter U5 to begin counting. The first count is zero, causing the TC (terminal count) pin to become logic low. This output remains low for the next 15 counts regardless of the input from U11B, due to the feedback from its output to the other input of NOR gate U4C. On count 16, the TC becomes high for a period of 200ms. During this period, the downstream load is enabled. If the comparators determine the voltage difference is within limits, the counter stops with the TC output

Data Sheet Download

www.linear.com/LTC4370

Linear Technology Corporation

remaining logic high, enabling the load. If the voltage difference is not within limits, the counter begins again, counting to 15 with the TC output a logic low. In this way, the load is enabled for 200ms every 3.2 seconds until the fault condition is cleared. The clock is provided by U4D, a hysteretic relaxation oscillator with a period of 200ms determined by R14 and C7. U1 is the LTC4370, which provides the current sharing function. The threshold is set to 300mV by R1. Operation of this device is described in the data sheet. Power for the additional circuitry is derived from VCC of the LTC4370. Summary The LTC4370 is designed primarily as a current sharing, diode-OR controller for two redundant supplies. With a few additional components, it can be easily be used in a non-redundant supply environment as a robust load sharing controller, where both of the supplies are necessary to support the entire load. The solution described here provides that function.

For applications help, call (408) 432-1900 dn1036f LT 1115 • PRINTED IN THE USA

1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900



FAX: (408) 434-0507 ● www.linear.com

 LINEAR TECHNOLOGY CORPORATION 2015

Using a Current Sharing Controller with Non ... - Linear Technology

diodes. In this way, the LTC4370 can actively balance .... 2m. 1%. GA. TE1. FETON1. FETON2. OUT2. COMP. 10. 9. 8. 7. 3. EN1. EN1. V ... call (408) 432-1900.

204KB Sizes 2 Downloads 249 Views

Recommend Documents

High Current Step-Down Controller Regulates to ... - Linear Technology
a DC/DC converter solution with high efficiency and small size. The LTC3832 also ... soft-start voltage ramp rate in this circuit is set by CSS. Figure 4 shows the ...

DN547 - VID Controller with Phase Extender ... - Linear Technology
PHASE 3. PHASE 4. FROM µP. NOTE: THIS IS A SIMPLIFIED SCHEMATIC. REFER TO. THE DATA ... One way to meet these demands is to use the LTC3877.

DN547 - VID Controller with Phase Extender ... - Linear Technology
for high performance servers, network and computing systems continues ... L, LT, LTC, LTM, Linear Technology, the Linear logo, Burst Mode and. PolyPhase are ...

Current Account Sustainability in Brazil: A Non-linear ...
Jun 29, 2009 - Email: [email protected]. ‡. Corresponding author, Paris School of ...... account balance is more responsive to negative shocks than to positive shocks. ... transition variable are reported in Tables 8-9 and 12-13 (for two ...

DN566 - Quad IO-Link Master with Higher Current ... - Linear Technology
In addition to the data pin (C/Q), the IO-Link Type A ... When the active driver changes state, it will generate ... swap channels as higher current SIO drivers.

DN503 - Dual DC/DC Controller for DDR Power ... - Linear Technology
Design Note 503. Ding Li. Introduction .... of frequent and large load steps—an important design consideration. Test results ... application. VTT Supply. The VTT ...

High Efficiency 4-Switch Buck-Boost Controller ... - Linear Technology
tween operating regions is ideal for automotive, telecom and battery-powered systems. Higher input voltage is easily enabled by adding a high voltage gate ...

Multiphase DC/DC Controller Pushes Accuracy ... - Linear Technology
Design Note 434. Tick Houk ... today's most demanding power supply applications: high current, low .... For single-output multiphase applications, the LTC3811.

DN505 - Dual Controller Provides 2μs Step ... - Linear Technology
Introduction. The LTC®3838 is a dual output, dual phase buck controller that employs a controlled constant on-time, valley current mode architecture to provide ...

Dual PowerPath™ Controller Simplifi es Power ... - Linear Technology
Dual PowerPath™ Controller Simplifies Power Management. Design Note 160. Jaime Tseng. 08/97/160_conv. Figure 1. Protected Automatic Switchover ...

DN505 - Dual Controller Provides 2μs Step ... - Linear Technology
The remotely sensed VOUT1 has a voltage regulation ac- curacy of 0.67% ... L, LT, LTC, LTM, Linear Technology, the Linear logo and PolyPhase are registered.

Determine Balancing Current for the LTC3305 ... - Linear Technology
In this way, the PTC acts as a constant power ... Figure 3 shows RTOTAL superimposed on the I-V characteristic curve of ... call (978) 656-4700. Figure 4. Design ...

Versatile Current Source Safely and Quickly ... - Linear Technology
from Large Capacitors to Batteries – Design Note 405. David Ng. 12/06/405_conv .... application where a controlled current source is needed, with almost no ...

Learning Multiple Non-Linear Sub-Spaces using K ... - GitHub Pages
complex domains such as computer vision where the raw input is not easily tamed ... algorithm, and can model subspaces of any degree of com- plexity via the ...

LINEAR AND NON LINEAR OPTIMIZATION.pdf
and x1 x2 x3 ≥ 0. 10. 5. a) What is a unimodal function ? What is the difference between Newton and. Quasi Newton methods ? 6. b) Explain univariate method.

LINEAR & NON-LINEAR OPTIMIZATION.pdf
x1 ≥ 0, x2 ≥ 0, x3 ≥ 0 and x4 ≥ 0. 10. 5. a) Explain the following methods with the help of flow-chart. i) Powell's method. ii) Steepest Descent Method. 10.

System Monitor with Instrumentation-Grade ... - Linear Technology
thermometers, one dry (dry bulb) and one covered in a fabric saturated ... All other trademarks are the property of their respective owners. LTC2991. DC590B.

Designing with a New Family of Instrumentation ... - Linear Technology
Designing with a New Family of Instrumental Amplifiers. Design Note 40. Jim Williams ... The classic application for these devices is bridge mea- surement.

Sharing Equality is Linear
Labels: there are three kind of nodes, application, abstrac- tion, and variable nodes, distinguished by a label that is respectively App, Lam, or Var. 2. Children and Binders: • Applications: an App node has exactly two children, called left and ri

Non-Linear Models
An optional data frame for the variables (and sometimes parameters). start. A list or numeric vector specifying the starting values for the parameters in the model.

TCPS Controller Design Using Fuzzy Logic Controller for Power ...
For economic and ecological reasons, the building of new transmission lines and expansion of existing transmission systems are becoming more and more difficult. In this new situation, it is necessary to utilize the existing power transmission system

Non-Linear Oscillations and Chaos
code can be found in the file vanDerPolSolution in the Mathematica folder under Computing ... equilibrium position, and it has a linear velocity v0 at that time.

BioPharm - Non-Linear Pharmacokinetics - PharmaDost.PDF ...
Page 1 of 5. www.PharmaDost.info. Page 1 of 5. Page 2 of 5. www.PharmaDost.info. Page 2 of 5. Page 3 of 5. www.PharmaDost.info. Page 3 of 5. Page 4 of 5.

Non-convex Optimization for Linear System with ...
Jul 15, 2010 - probabilities than subgaussian and gaussian random variables. Geometrically, perpendicular in l2 needs to be generalized in lp. The analogue ...