深圳市双盈液晶显示有限公司 TEL:15889769673

SPECIFICATION LCD MODULE FH-68005_V2 Revision: A

REVISION RECORD DESIGN VERSION

A

CHECK

REVIEW

DATE

CONTENTS

2010.11.03

First Release

CUSTOMER

Customer company:

Date:

Customer signature:

Date:

FH-68005_V2

Version :A

1 / 16

深圳市双盈液晶显示有限公司 TEL:15889769673

CONTENTS GENERAL INFORMATION ABSOLUTE MAXIMUM RATINGS ELECTRICAL CHARACTERISTICS TIMING OF POWER SUPPLY BACKLIGHT CHARACTERISTICS EXTERNAL DIMENSIONS INTERFACE SIGNALS ELECTRO-OPTICAL CHARACTERISTICS RELIABILITY TEST QUALITY LEVEL TOUCH PANEL CHARACTERISTICS PACKAGING DRAWING PRECAUTINGS FOR USE OF LCD MODULES

FH-68005_V2

Version :A

2 / 16

深圳市双盈液晶显示有限公司 TEL:15889769673 GENERAL INFORMATION Item Driver element Viewing direction TP V/A (W × H) Active area (W×H) Number of Dots Driver IC Colors Weight Backlight Type Interface Type Input voltage

Contents

Unit

a-Si TFT active matrix 12:00 45.2×63.5 43.2×57.6 240(RGB)×320 RM68050/ILI9328 262K TBD LED Parallel 2.8

-O’ Clock mm mm Pixel --g --V

ABSOLUTE MAXIMUM RATINGS Parameter Supply voltage for logic Input voltage Operating temperature Storage temperature Humidity

Symbol VDD VIN TOP TST RH

Min -0.3 -0.3 -10 -20 -

Max 3.3 VDD+0.3 60 70 90%(Max60℃)

Unit V V ℃ ℃ RH

ELECTRICAL CHARACTERISTICS DC CHARACTERISTICS Parameter Supply voltage for logic Supply voltage for analog Supply voltage for interface I/O I/O leakage current

Input voltage ′H′level Input voltage ′L′level Output voltage ′H′level Output voltage ′L′level

Symbol VDD-VSS Vcc IOVcc Idd VIH VIL VOH VOL

Min 2.5 － － -1.0 0.8*Iovcc -0.3v 0.8*Iovcc －

Typ － － － － － －

Max 3.3 － － 1.0 IOVCC 0.2*Iovcc － 0.2*Iovcc

TIMING OF POWER SUPPLY PLEASE REFER TO THE DRIVER IC SPECIFICATION.

BACKLIGHT CHARACTERISTICS Item Forward voltage Luminance Number of LED Connection mode

Symbol Vf LV p

Min 2.9 3000

Typ 3.2 3300 4 Parallel

Max 3.4 -

Unit V cd/㎡ Piece -

EXTERNAL DIMENSIONS FH-68005_V2

Version :A

3 / 16

Condition If=60 mA -

Unit V V V mA V V V V

1

双盈液晶显示

SHUANGYINGYEJING

1

FH-68005_V2

68.60

Version :A

2

PIN1

XL

2

4 / 16

A K4

XR

3.10

3

0.25

0.12

4

TOLERANCE

0
(不包括背面双面胶)

3.45max

4

LEVEL-2

1 Of 1

A4

YXT-BL2.8-01-YY/MM/DD

A1

5

wang

5

REV

6

双盈液晶显示有限公司

2010.11.03

FH--68005

FH--68005 MODULE DRAWING

wang

wang

11.03

6

wang

33±2.0

K1 K2 K3

LED Source (CIRCUIT DIAGRAM)

0.35 0.50 P0.5X39=19.50

PIN4

YD

YU

47.20 43.20

3

A1

深圳市双盈液晶显示有限公司 TEL:15889769673

4.50

33.2

11.90

57.60

2.60

深圳市双盈液晶显示有限公司 TEL:15889769673

Interface Signals Pin No.

Symbol

Level

1~4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

DB0~DB3 GND VCC CS RS WR RD IM0 X+ Y+ XYLEDA LEDK1 LEDK2 LEDK3 LEDK4

H/L H/L 2.8V H/L H/L H/L H/L H/L -

21 22 23~30 31 32~33 34 35~37 38~40

IM3 DB4 DB8~DB15 RESET VCC GND DB5~DB7 NC

H/L

Select 16/8bit

H/L H/L H/L H/L VSS H/L ---

Data bus Data bus Reset pin Power supply for LCM Power ground Data bus NO CONNECT

-

-

Description Back light power line Back light power line Power supply for LCM Chip select Command/data select pin Write execution control pin Read execution control pin Select 16/8bit TP PIN TP PIN TP PIN TP PIN Back light power line Back light power line Back light power line Back light power line Back light power line

APPLICATION CIRCUIT Please consult our technical department for detail information.

INITIAL CODE Please consult our technical department for detail information.

FH-68005_V2

Version :A

5 / 16

深圳市双盈液晶显示有限公司 TEL:15889769673

ELECTRO-OPTICAL CHARACTERISTICS Item Response time Contrast ratio Luminance uniformity Surface Luminance

Symbol Condition Min Typ Max Unit Remark 25 ms Tr+Tf Note 4& FIG. 1 Cr 300 Note 1& FIG. 2 θ=0° ∅=0° δ 80 % Note 2 Ta=25℃ WHITE LV 185 203 cd/㎡ Note 3 ∅=90° 50 50 deg ∅=270° 50 50 deg Note 6& FIG. 3 Viewing angle range θ ∅=0° 35 55 deg ∅=180° 45 60 deg x 0.6457 Red y 0.3391 x 0.3438 Green θ=0° y 0.6012 CIE(x,y) ∅=0° Note 5. chromaticity x 0.1476 Ta=25℃ Blue y 0.1110 x 0.313 -White y 0.329 Note 1. Contrast Ratio(CR) is defined mathematically as For more information see FIG 2.: Contrast Ratio = Average Surface Luminance with all white pixels (P 1,P2, P 3,P4, P5) Average Surface Luminance with all black pixels (P1, P2, P3,P4, P5) Note 2. Surface luminance is the LCD surface from the surface with all pixels displaying white. For more information see FIG 2. Lv = Average Surface Luminance with all white pixels (P1, P2, P 3,P4, P5) Note 3. The uniformity in surface luminance , δ WHITE is determined by measuring luminance at each test position 1 through 5, and then dividing the maximum luminance of 5 points luminance by minimum luminance of 5 points luminance. For more information see FIG 2. δ WHITE = Minimum Surface Luminance with all white pixels (P1, P2, P 3,P4,P5) Maximum Surface Luminance with all white pixels (P1, P2, P 3,P4, P5) Note 4. Response time is the time required for the display to transition from White to black(Rise Time, Tr) and from black to white(Decay Time, Tf). For additional information see FIG 1. The test equipment is Autronic-Melchers’s ConoScope. series Note 5. CIE (x, y) chromaticity,The x,y value is determined by measuring luminance at each test position 1 through 5,and then make average value. Note 6. Viewing angle is the angle at which the contrast ratio is greater than 2. For TFT module the contrast ratio is greater than 10. The angles are determined for the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the LCD surface. For more information see FIG 3. Note7. For Viewing angle and response time testing, the testing data is base on FH-68005_V2

Version :A

6 / 16

深圳市双盈液晶显示有限公司 TEL:15889769673 Autronic-Melchers’s ConoScope. Series Instruments. For contrast ratio, Surface Luminance, Luminance uniformity,CIE The test data is base on TOPCON’s BM-7 photo detector.

FIG. 1 The definition of Response Time The response time is defined as the following figure and shall be measured by switching the input signal for “black” and “white”.

FIG. 2 Measuring method for Contrast ratio,surface luminance, Luminance uniformity ， CIE (x, y) chromaticity

A : 5 mm B : 5 mm H,V : Active Area Light spot size ∅=7mm, 500mm distance from the LCD surface to detector lens measurement instrument is TOPCON’s luminance meter BM-5 FIG. 3 The definition of viewing angle

FH-68005_V2

Version :A

7 / 16

深圳市双盈液晶显示有限公司 TEL:15889769673

RELIABILITY TEST Reliability test conditions ( Polarizer characteristics null ) No. 1 2 3 4 5 6

7 8

Test Items High Temperature Storage Low Temperature Storage High Temperature Operating Low Temperature Operating High Temp. and High Humidity Operating Thermal Shock Packing Shock Packing Vibration

Test Condition T = 70℃ for 200hr T = -20℃ for 200hr T = 60℃ for 120hr T = -10℃ for 120hr (But no condensation of dew) T = 50℃ /90% for 120hr (But no condensation dew) -10±2℃~25~60±2℃×10cycles (30min.) (5min.) (30min.) 1corner, 3edge, 6face / 76cmDrop Random 1.06Grms XYZ 30min for each direction

Remarks

Module (Without Contamination)

Packing

※ 1) No.1~ No.6 : No guarantee for panel, only for module with the above test conditions. 2) No.7~ No.8 : Refer to 7-1) Packing Ass’y on page 14. Result Evaluation Criteria FH-68005_V2

Version :A

8 / 16

深圳市双盈液晶显示有限公司 TEL:15889769673 TFT- LCD Panel should be at room temperature for 2 hours when the display quality test is over. There should be no particular change which might affect the practical display function and the display quality test should be conducted under normal operating condition.

Quality level Outgoing Quality Standard. 1 Sample plan Sampling plan according to GB/T2828.1-2003/ISO 2859-1：1999 and ANSI/ASQC Z1.4-1993, normal level 2 and based on: Major defect: AQL 0.65 Minor defect: AQL 1.5 2. Inspection condition Viewing distance for cosmetic inspection is about 30cm with bare eyes, and under an environment of 20~40W light intensity, all directions for inspecting the sample should be within 45°against perpendicular line. 3. Definition of inspection zone in LCD.

A

B C

Zone A: character/Digit area Zone B: viewing area except Zone A (Zone A + Zone B=minimum Viewing area) Zone C: Outside viewing area (invisible area after assembly in customer’s product) Fig.1 Inspection zones in an LCD. Note: As a general rule, visual defects in Zone C are permissible, when it is no trouble for quality and assembly of customer’s product.

FH-68005_V2

Version :A

9 / 16

深圳市双盈液晶显示有限公司 TEL:15889769673

4.Standards of inspection items 4.1Major Defect Item No

4.1.1

Items to be inspected All functional defects

Classificatio n of defects

Inspection Standard 1.No display 2.Display abnormally 3.Missing vertical，horizontal segment 4.Short circuit 5. Back-light no lighting, flickering and abnormal lighting. Missing component

4.1.2

Missing

4.1.3

Outline dimension

Overall outline dimension beyond the drawing is not allowed.

4.1.4

linearity

No more than 1.5%

Major

4.2 Cosmetic Defect Item No

Items to be inspected

Classification of defects

Inspection Standard For dark/white spot, sizeΦis defined

Clear Spots Black and white Spot defect Pinhole, Foreign Particle, polarizer Dirt

4.21

as Φ=(x + y) 2 1 Acceptable Qty

Zone Size(mm)

Minor A

Φ≤0.15 0.15＜Φ≤0.20 0.20＜Φ≤0.30 Φ＞0.30 2

Ignore 2 1 0

Dim Spots Circle shaped and dim edged defects

Size(mm)

A

Φ≤0.15 0.15＜Φ≤0.20 0.20＜Φ≤0.30 Φ＞0.30 3

Φ≤0.2 0.20＜Φ≤0.40

FH-68005_V2

Ignore

B

C Minor

Ignore 2 1 0

Zone Size(mm)

C

Acceptable Qty

Zone Clear Spots TP Dirt

B

Ignore

Acceptable Qty A

B Ignore 2

Version :A

Minor

C Ignore

10 / 16

深圳市双盈液晶显示有限公司 TEL:15889769673 0.40＜Φ≤0.60 Φ＞0.60

1 0

4.2 Cosmetic Defect Item No

Items to be inspected Size(mm) Line defect Black line, White line, Foreign material on polarizer

4.2.2

Foreign material on TP film

4.2.3

Dim line defect Polarizer scratch TP film scratch

Classification of defects

Inspection Standard Acceptable Qty Zone L(Length)

W(Width) A

B

C

Ignore L≤3.0 L≤3.0

W≤0.01 Ignore 0.01＜W≤0.03 2 Ignore 0.03＜W≤0.05 1 W＞0.05 0 The line can be seen after mobile phone in the operating condition: Size(mm) Acceptable Qty

Minor

Zone L(Length)

W(Width) A

B

C

W≤0.03 Ignore 0.03＜W≤0.05 3 Ignore W＞0.05 0 If the scratch can be seen after mobile phone cover assembling or in the operating condition, judge by the line defect of 4.2.2. If the scratch can be seen only in non-operating condition or some special angle, judge by the following. Size(mm) Acceptable Qty Zone L(Length) W(Width) A B C Ignore W≤0.03 Ignore 5.0＜L≤10.0 0.03＜W≤0.05 2 Ignore L≤5.0 0.05＜W≤0.08 1 W＞0.08 0

Minor

Ignore L≤5.0

Minor

Air bubbles between glass & polarizer Acceptable Qty

Zone 4.2.4

Polarize Air bubble

Size(mm)

A

Φ≤0.25 0.25＜Φ≤0.5 Φ＞0.50

FH-68005_V2

B Ignore 2 0

Version :A

C

Ignore

11 / 16

Minor

深圳市双盈液晶显示有限公司 TEL:15889769673

Item No

Items to be inspected

Classification of defects

Inspection Standard (i) Chips on corner A:LCD Glass defect

X(mm) Y(mm) Z(mm) ≤2.0 ≤S Disregard Notes: S=contact pad length Chips on the corner of terminal shall not be allowed to extend into the ITO pad or expose perimeter seal. B:TP Glass defect

4.35

Glass defect

X(mm) ≤3.0 (ii)Usual surface cracks A:LCD Glass defect

Y(mm) ≤3.0

X(mm) Y(mm) ≤3.0
X(mm) ≤6.0

FH-68005_V2

Y(mm) ＜2.0

Version :A

Z(mm) Disregard

Z(mm) Disregard

Z(mm) Disregard

12 / 16

Minor

深圳市双盈液晶显示有限公司 TEL:15889769673 (iii) Crack Cracks tend to break are not allowed.

Touch panel characteristics Operation life

Electric characteristics

Tapping durability Pen sliding durability Operation force Electric characteristics Insulation resistance Linearity Chattering Time

>1,000,000 times >1,000,00 times 10-100g Film：400~950Ω，Glass：200~600Ω ≥10MΩ (DC25V) ≤1.5% <10ms

Structure, and Area definition

Area-(A) : Active area The area guarantees a touch panel operation with the following characteristics when pressed. (ⅰ) Operation force (ⅱ) Electric characteristics (ⅲ) Tapping durability (ⅳ) Pen sliding durability Area-(B) : Operation non-guaranteed area The area does not guarantee a touch panel operation and its function. When this area is pressed, touch panel shows degradation of its performance and durability such as a pen sliding durability becomes about one-tenth compared with the active area (Area- (A) as guaranteed area) and its operation force requires about double. About 0.5 mm outside from a boundary of the active area corresponds to this area. Area-(C) : Pressing prohibition area The area forbids pressing because an excessive load is applied to a transparent electrode and a serious damage is given to a touch panel function by pressing. About 0.5mm outside from a boundary of Area-(B)” the operation non-guaranteed area” corresponds to this area. FH-68005_V2

Version :A

13 / 16

深圳市双盈液晶显示有限公司 TEL:15889769673 Area-(D) : Non-Active area (Frame) The area does not activate even if pressed. (Remark: In order to prevent unusual performance degradation and malfunction of a touch panel, please inspect firstly whether the set case designing and touch panel assembling method are reasonable or not.) Area-(B)+Area-(C)：Sensitive area Area–(B) and area-(C) both belong to the sensitive area. This area has a clearance between top and bottom contact side. Great press resulting in transparent electrode cracks, function defect to be exact, will deform surface transparent electrode. Please think about structure of sensitive area and case in order to avoid terminal user to fail to touch this area.

Packaging Drawing TBD

Precautions for Use of LCD Modules 1. Handling Precautions (1) The display panel is made of glass and polarizer. As glass is fragile. It tends to become or chipped during handling especially on the edges. Please avoid dropping or jarring. Do not subject it to a mechanical shock by dropping it or impact. (2) If the display panel is damaged and the liquid crystal substance leaks out, be sure not to get any in your mouth. If the substance contacts your skin or clothes, wash it off using soap and water. (3) Do not apply excessive force to the display surface or the adjoining areas since this may cause the color tone to vary. Do not touch the display with bare hands. This will stain the display area and degraded insulation between terminals (some cosmetics are determined to the polarizer). (4) The polarizer covering the display surface of the LCD module is soft and easily scratched. Handle this polarizer carefully. Do not touch, push or rub the exposed polarizers with anything harder than an HB pencil lead (glass, tweezers, etc.). Do not put or attach anything on the display area to avoid leaving marks on. Condensation on the surface and contact with terminals due to cold will damage, stain or dirty the polarizer. After products are tested at low temperature they must be warmed up in a container before coming is contacting with room temperature air. (5) If the display surface becomes contaminated, breathe on the surface and gently wipe it with a soft dry cloth. If it is heavily contaminated, moisten cloth with one of the following solvents - Isopropyl alcohol - Ethyl alcohol Do not scrub hard to avoid damaging the display surface. (6) Solvents other than those above-mentioned may damage the polarizer. Especially, do not use the following. - Water

FH-68005_V2

Version :A

14 / 16

深圳市双盈液晶显示有限公司 TEL:15889769673 - Ketone - Aromatic solvents Wipe off saliva or water drops immediately, contact with water over a long period of time may cause deformation or color fading. Avoid contacting oil and fats. (7) Exercise care to minimize corrosion of the electrode. Corrosion of the electrodes is accelerated by water droplets, moisture condensation or a current flow in a high-humidity environment. (8) Install the LCD Module by using the mounting holes. When mounting the LCD module make sure it is free of twisting, warping and distortion. In particular, do not forcibly pull or bend the I/O cable or the backlight cable. (9) Do not attempt to disassemble or process the LCD module. (10) NC terminal should be open. Do not connect anything. (11) If the logic circuit power is off, do not apply the input signals. (12) Electro-Static Discharge Control，Since this module uses a CMOS LSI, the same careful attention should be paid to electrostatic discharge as for an ordinary CMOS IC. To prevent destruction of the elements by static electricity, be careful to maintain an optimum work environment. - Before remove LCM from its packing case or incorporating it into a set, be sure the module and your body have the same electric potential. Be sure to ground the body when handling the LCD modules. - Tools required for assembling, such as soldering irons, must be properly grounded. make certain the AC power source for the soldering iron does not leak. When using an electric screwdriver to attach LCM, the screwdriver should be of ground potentiality to minimize as much as possible any transmission of electromagnetic waves produced sparks coming from the commutator of the motor. - To reduce the amount of static electricity generated, do not conduct assembling and other work under dry conditions. To reduce the generation of static electricity be careful that the air in the work is not too dried. A relative humidity of 50%-60% is recommended. As far as possible make the electric potential of your work clothes and that of the work bench the ground potential - The LCD module is coated with a film to protect the display surface. Exercise care when peeling off this protective film since static electricity may be generated （13）Since LCM has been assembled and adjusted with a high degree of precision, avoid applying excessive shocks to the module or making any alterations or modifications to it. - Do not alter, modify or change the shape of the tab on the metal frame. - Do not make extra holes on the printed circuit board, modify its shape or change the positions of components to be attached. - Do not damage or modify the pattern writing on the printed circuit board. - Absolutely do not modify the zebra rubber strip (conductive rubber) or heat seal connector. 15 / 16 FH-68005_V2 Version :A

深圳市双盈液晶显示有限公司 TEL:15889769673 - Except for soldering the interface, do not make any alterations or modifications with a soldering iron. - Do not drop, bend or twist LCM.

2. Storage precautions 2.1 When storing the LCD modules, avoid exposure to direct sunlight or to the light of fluorescent lamps. 2.2 The LCD modules should be stored under the storage temperature range. If the LCD modules will be stored for a long time, the recommend condition is: Temperature :

0℃ ～ 40℃

Relatively humidity:

≤80%

2.3 The LCD modules should be stored in the room without acid, alkali and harmful gas. 3 The LCD modules should be no falling and violent shocking during transportation, and also should avoid excessive press, water, damp and sunshine.

--------- END

FH-68005_V2

Version :A

16 / 16