Application Note 119A April 2008 Powering Complex FPGA-Based Systems Using Highly Integrated DC/DC µModule Regulator Systems Part 1 of 2 Circuit and Electrical Performance Alan Chern and Afshin Odabaee In a recent discussion with a system designer, the requirement for his power supply was to regulate 1.5V and deliver up to 40A of current to a load that consisted of four FPGAs. This is up to 60W of power that must be delivered in a small area with the lowest height profile possible to allow a steady flow of air for cooling. The power supply had to be surface mountable and operate at high enough efficiency to minimize heat dissipation. He also demanded the simplest possible solution so his time could be dedicated to the more complex tasks. Aside from precise electrical performance, this solution had to remove the heat generated during DC to DC conversion quickly so that the circuit and the ICs in the vicinity do not overheat. Such a solution requires an innovative design to meet these criteria:

contribute to lower system cost, consuming less power to remove heat). Figure 1 shows a test board for such a circuit. The design regulates 1.5V output while delivering 40A (up to 48A) of load current. Each “black square” is a complete DC/DC circuit and is housed in a 15mm × 15mm × 2.8mm surface mount package. With a few input and output capacitors and resistors, the design using these DC/DC µModule® regulator systems is as simple as it’s shown in the photo.

1. Very low profile to allow efficient air flow and to prevent thermal shadow on surrounding ICs 2. High efficiency to minimize heat dissipation 3. Current sharing capability to spread the heat evenly to eliminate hot spots and minimize or eliminate the need for heat sinks 4. Complete DC/DC circuit in a surface mount package that includes the DC/DC controller, MOSFETs, inductor, capacitors and compensation circuitry for a quick and easy solution Innovation in DC/DC Design The innovation is a modular but surface mount approach that uses efficient DC/DC conversion, precise current sharing and low thermal impedance packaging to deliver the output power while requiring minimal cooling. Because of the low profile and power sharing among four devices, a system using this solution depends on fewer fans or a slower fan speed as well as few or no heat sinks. (These

Figure 1. Four DC/DC µModule Regulator Systems Current Share to Regulate 1.5V at 48A with Only 2.8mm Profile and 15mm × 15mm of Board Area. Each µModule Regulator Weighs Only 1.7g and Has an IC Form-Factor That Can Easily Be Used with Any Pick-and-Place Machine During Board Assembly

DC/DC µModule Regulators: Complete Systems in an LGA Package The LTM4601 µModule DC/DC regulator is a high performance power module shrunk down to an IC form factor. It is a completely integrated solution—including the PWM controller, inductor, input and output capacitors, ultralow RDS(ON) FETs, Schottky diodes and compensation circuitry. Only external bulk input and output capacitors and one resistor are needed to set the output from 0.6V to 5V. The L, LT, LTC, LTM, µModule, Linear Technology and the Linear logo are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners.

an119afc

AN119A-1

Application Note 119A VOUT

CLOCK SYNC 0° PHASE

VIN 4.5V TO 20V 51.1k

51.1k

PGOOD

59k LTC6902 V+ SET DIV MOD PH GND OUT1 OUT4 OUT2 OUT3

0.1µF

+

MPGM RUN COMP INTVCC DRVCC

CIN* 100µF 25V 10µF 25V ×2

392k

PLLIN TRACK/SS VOUT

VIN PGOOD

LTM4601

SGND

PGND

5% MARGIN

4-PHASE OSCILLATOR

VFB MARG0 MARG1

TRACK/SS CONTROL

VOUT 1.5V 48A MAX

220pF 22µF 6.3V 470µF 6.3V

VOUT_LCL DIFFVOUT VOSNS+ VOSNS–

fSET

60.4k + R SET N RSET N = NUMBER OF PHASES VOUT = 0.6V

RSET 10k

+

120pF

MARGIN CONTROL CLOCK SYNC 90° PHASE

4.5V TO 20V

TRACK/SS CONTROL VIN PGOOD

PGOOD

MPGM RUN COMP INTVCC DRVCC

10µF 25V ×2

PLLIN TRACK/SS VOUT

LTM4601-1

392k SGND

PGND

VFB MARG0 MARG1

22µF 6.3V

+

VOUT_LCL NC3 NC2 NC1

470µF 6.3V

fSET

CLOCK SYNC 180° PHASE 4.5V TO 20V

TRACK/SS CONTROL VIN PGOOD

PGOOD

MPGM RUN COMP INTVCC DRVCC

10µF 25V ×2

PLLIN TRACK/SS VOUT

LTM4601-1

392k SGND

PGND

VFB MARG0 MARG1

22µF 6.3V

+

VOUT_LCL NC3 NC2 NC1

470µF 6.3V

fSET

CLOCK SYNC 270° PHASE 4.5V TO 20V

TRACK/SS CONTROL VIN PGOOD

PGOOD

MPGM RUN COMP INTVCC DRVCC

10µF 25V ×2

0.1µF

PLLIN TRACK/SS VOUT

LTM4601-1

392k SGND

PGND

VFB MARG0 MARG1 VOUT_LCL NC3 NC2 NC1

22µF 6.3V

+

470µF 6.3V

fSET an119a F02

*CIN OPTIONAL TO REDUCE ANY LC RINGING. NOT NEEDED FOR LOW INDUCTANCE PLANE CONNECTION

Figure 2. Simply Parallel Multiple DC/DC µModule Regulator Systems to Achieve Higher Output Current. Board Layout Is as Easy as Copying and Pasting Each µModule Regulator’s Layout With Very Few External Components Required

an119afc

AN119A-2

Application Note 119A supply can produce 12A (more, if paralleled) from a wide input range of 4.5V to 20V, making it extremely versatile. The pin-compatible LTM4601HV extends the input range to 28V. Another significant advantage of the LTM4601 over powermodule- or IC-based systems is its ability to easily scale up as loads increase. If load requirements are greater than one µModule regulator can produce, simply add more modules in parallel. The design of a parallel system involves little more than copying and pasting the layout of each 15mm × 15mm µModule regulator. Electrical layout issues are taken care of within the µModule package—there are no external inductors, switches or other components to worry about. Output features include output voltage tracking and margining. The high switching frequency, typically 850kHz at full load, constant on-time, zero latency controller delivers fast transient response to line and load changes while maintaining stability. Should frequency harmonics be a concern, an external clock can control synchronization via an on-chip phase-locked loop. 48A from Four Parallel DC/DC µModule Regulators Figure 2 shows a regulator comprising four parallel LTM4601s, which can produce a 48A (4 × 12A) output. The regulators are synchronized but operate 90° out-ofphase with respect to each other, thereby reducing the amplitude of input and output ripple currents through cancellation (Figure 3). Synchronization and phase shifting is implemented via the LTC6902 oscillator, which provides four clock outputs, each 90° phase shifted (for 2- or 3-phase relationships, the LTC6902 can be adjusted via a resistor). By operating the µModule regulators out-of-phase, peak input and output current is reduced by approximately 20% depending on the duty cycle (see the LTM4601 data sheet). The attenuated ripple, in turn, decreases the external capacitor RMS current rating and size requirements, further reducing solution cost and board space.

The clock signals serve as input to the PLLIN (phase-locked loop in) pins of the four LTM4601s. The phase-locked loop of the LTM4601 is comprised of a phase detector and a voltage controlled oscillator, which combine to lock onto the rising edge of an external clock with a frequency range of 850kHz. The phase-locked loop is turned on when a pulse of at least 400ns and 2V amplitude at the PLLIN pin is detected, though it is disabled during start-up. Figure 3 shows the switching waveforms of four LTM4601 µModule regulators in parallel.

1µs/DIV

an119a F03

Figure 3. By Operating Each DC/DC µModule Regulator 90° Outof-Phase, the Input and Output Ripples Are Reduced, Which Also Reduces the Requirement for Input and Output Capacitors. Photo Shows Individual µModule Regulator Switching Waveforms for Figure 2

Only one resistor is required to set the output voltage. In a parallel set-up, the value of the resistor depends on the number of LTM4601s used. This is because the effective value of the top (internal) feedback resistor changes as you parallel LTM4601s. The LTM4601’s reference voltage is 0.6V and its internal top feedback resistor value is 60.4kΩ, so the relationship between VOUT, the output voltage setting resistor (RFB), and the number of modules (n) placed in parallel is:



VOUT

60.4k +RFB n = 0.6V RFB

an119afc

Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.

AN119A-3

Application Note 119A 100 90

12V

EFFICIENCY (%)

80

VIN 5V/DIV

70 60

0V

50

VOUT 1V/DIV

40 3.3VOUT 2.5VOUT 1.8VOUT 1.5VOUT 1.2VOUT

30 20 10 0

0

10

ILOAD 20A/DIV

20 30 LOAD CURRENT (A)

VIN = 12V VOUT = 1.5V LOAD = 40A

50

40

an119a F04

Figure 4. Efficiency of the Four DC/DC µModule Regulators in Parallel Remains High Over a Wide Range of Output Voltages (12V Input)

Figure 4 illustrates the system’s high efficiency over the vast output current range up to 48A. The system performs impressively with no dipping in the efficiency curve for a broad range of output voltages.

The soft-start feature of the LTM4601 prevents large inrush currents at start-up by slowly ramping the output voltage to its nominal value. The relation of start-up time to VOUT and the soft-start capacitor (CSS) is:

(

)

an119a F05

Figure 5. Controlled Soft-Start Is Important in Proper Start-Up of the FPGA or the System as a Whole; Soft-Start Current and Voltage Ramp for Four DC/DC µModule Regulators in Parallel

VIN 5V/DIV

IOUT(IC1) 5A/DIV

Start-Up, Soft-Start and Current Sharing

tSOFTSTART =0.8 • 0.6V-VOUT(MARGIN) •

2ms/DIV

CSS 1.5µA

IOUT(IC2) 5A/DIV VIN = 12V VOUT = 1.5V LOAD = 20A

5ms/DIV

an119a F06

Figure 6. Each DC/DC µModule Regulator Starts and Ends By Sharing the Load Current Evenly and Balanced, a Crucial Feature to Prevent One Regulator from Overheating; Two Parallel LTM4601s, as Each Rises to a Nominal 10A Each, 20A Total

where

VOUT(MARGIN) =

Conclusion

%VOUT • VOUT 100

For example, a 0.1µF soft-start capacitor yields a nominal 8ms ramp (see Figure 5) with no margining. Current sharing among parallel regulators is well balanced through start-up to full load. Figure 6 shows an evenly distributed output current curve for a 2-parallel LTM4601 system, as each rises to a nominal 10A each, 20A total.

The DC/DC µModule regulators are self-contained and complete systems in an IC form factor. The low profile, high efficiency and current sharing capability allow practical high power solutions for the new generation of digital systems. Thermal performance is impressive at 48A of output current with balanced current sharing and smooth uniform start-up. The ease and simplicity of this design minimizes development time while saving board space. In part two of this discussion, the focus will be on thermal performance and layout of this circuit.

an119afc

Linear Technology Corporation

McCarthy Blvd., Milpitas, CA 95035-7417 AN119A-4 1630 (408) 432-1900 FAX: (408) 434-0507 www.linear.com ●



LT 0515 REV C • PRINTED IN USA

 LINEAR TECHNOLOGY CORPORATION 2008

Powering Complex FPGA-Based Systems Using ... - Linear Technology

Application Note 119A. AN119A- ... The design regulates 1.5V output while delivering. 40A (up ... output capacitors and resistors, the design using these. DC/DC ...

500KB Sizes 7 Downloads 203 Views

Recommend Documents

DN549 - Powering Altera Arria 10 FPGA and Arria ... - Linear Technology
Introduction. FPGA development kits allow system developers to evaluate an FPGA without having to design a complete system. Figures 1 and 2 show Altera's ...

Preconditioning of complex symmetric linear systems ...
Feb 22, 2013 - problems arise in many applications, e.g., in acoustics, .... We call C positive, if (2.2) at least holds with cC = 0. ..... with center c = 1+i.

Complex adaptive systems
“By a complex system, I mean one made up of a large number of parts that ... partnerships and the panoply formal and informal arrangements that thy have with.

Using a Current Sharing Controller with Non ... - Linear Technology
diodes. In this way, the LTC4370 can actively balance .... 2m. 1%. GA. TE1. FETON1. FETON2. OUT2. COMP. 10. 9. 8. 7. 3. EN1. EN1. V ... call (408) 432-1900.

Using the LTC6900 Low Power SOT-23 Oscillator ... - Linear Technology
The LTC6900 master oscillator is controlled by the ratio of the voltage between V+ and the SET pin and the current,. IRES, entering the SET pin. As long as IRES ...

Fiber Optic Communication Systems Benefit from ... - Linear Technology
Noise Avalanche Photodiode Bias Supply – Design Note 273. Michael Negrete. 12/01/273_conv ... optic applications. The LT1930A, a capacitor-diode tripler ...

New 12-Bit Data Acquisition Systems ... - Linear Technology
New 12-Bit Data Acquisition Systems Communicate with. Microprocessors Over 4 Wires – Design Note 22. 05/89/22_conv. L, LT, LTC, LTM, Linear Technology ...

New 12-Bit Data Acquisition Systems ... - Linear Technology
New 12-Bit Data Acquisition Systems Communicate with. Microprocessors Over 4 Wires – Design Note 22. 05/89/22_conv. L, LT, LTC, LTM, Linear Technology ...

LTC1560-1 - Linear Technology
Gain vs Frequency of the 1MHz and 500kHz. Figure 1. A Typical ... 6. 5. GND. VIN. GND. V–. VOUT. SHDN. V+. 0.5fC/fC. 5V. 3. 1k. 2. 4. VOUT. 7. LT®1360. 5V. – 5V. 8 ... DC offset of the 1/2 LT1364 plus its offset current times the 10k resistor ..

DN172 - Linear Technology
response is excellent, with less than 5μs recovery time from a ±400mA ... Data Sheet Download ... LTC1504 is the best solution where efficiency, especially.

DN518 - Linear Technology
possible to produce a low noise supply in this way, it requires careful ... typical switching regulator, and (3) the LTM8028 low ... call (408) 432-1900, Ext. 3747.

DN375 - Linear Technology
call (408) 432-1900. RF FREQUENCY (GHz) ... For ACPR/AltCPR, center the measurement band 5MHz/10MHz above the center of the highest carrier. To find ...

DN531 - Linear Technology
SiR664DP. M2. SiR664DP. L1. 5.6µH. WÜRTH 7443556560. M3. SiR422DP. M5. SiR422DP. D6. B360A. C19. 0.22µF. 25V. 0603. C20. 0.22µF. 25V. 0603. C21.

eterna1 - Linear Technology
Dec 16, 2015 - ... If testing encompasses measuring ETERNA1's output power or PSD, ..... go to: http://csrc.nist.gov/groups/STM/cavp/documents/aes/aesval.html.

Linear Systems
in which a desk calculator may be used. By a ...... that are of significance in application to linear systems ..... (ro, 1p,) + 2 (App)a = (h,Ap) = (1h,p) = (k,p). OI".

a self powering wireless environment monitoring system using soil ...
a self powering wireless environment monitoring system using soil energy 06874554.pdf. a self powering wireless environment monitoring system using soil ...

ETERNA2 User's Guide - Linear Technology
Sep 30, 2016 - Radiotest commands use the parameter to define which channel or channels the radio ... Earlier versions of software should omit.

ETERNA2 User's Guide - Linear Technology
Sep 30, 2016 - SmartMesh Industrial and Eterna are trademarks of Dust Networks, Inc. The ..... Transmit: 128 bytes of data maximum + 5 bytes preamble/SFD ..... found to comply with the limits for a Class B digital device, pursuant to Part 15.

Market Requirements Template - Linear Technology
Dec 16, 2015 - Low-Rate Wireless Personal Area Networks (LR-WPANs) ..... See the R&TTE Directive, Article 12 and Annex VII for more information.

Design Note 1035 - Linear Technology
Design Note 1035. Tom Domanski. 10/15/1035. Introduction. A single LTC®2983temperature measurement device can support up to 18 2-wire RTD probes, ...

Science Meets Technology (Understanding Complex ...
Online PDF Complex Engineered Systems: Science Meets Technology ... Meets Technology (Understanding Complex Systems) Popular , Complex Engineered.

Monolithic Linear Battery Charger Operates from ... - Linear Technology
lead acid battery stack from a solar panel, though any combination of input and battery voltages are possible. The LTC4079's differential voltage regulation is.