LED plug has a LED with a current limiting resistor which can be used as indicator in various projects. This PCB design enables you to bend the LED to any position as per the user’s need and also this plug can be mounted anywhere using screws. This plug is available in different colors.
Specification
● Operating voltage: 5V ●
Size: 15mm x 20mm
Variants 1.
Diffused a. Red b. Yellow c. Green
2. Clear a. IR
Elint Labz (www.elintlabz.in)
Page 2 of 6
Product Manual: LED Plug
b. UV c. White d. Red e. Yellow f.
Green
g. Blue
Supported cables: 1.
3-3 A
2. 4-3 A
Details
LED plug is a digital output device. It has a interfacing port with three pins named as G, V & D. Here G represents Ground , V represents VCC and D represents Data pin through which LED is controlled.
How to interface?
Use either of the supported interface cables to connect this LED plug to the controller board. If 4-3A cable is to be used then 3pin end of the cable is connected the LED plug. If 3-3A wire is to be used then any end of the wire can be connected to the LED plug. Always ensure that black wire of the cable is connected to the G pin. In the below given pictures one can see 4-3A cable is used to connect LED plug to the Pluguino Board. The data pin of the LED plug is connected to the 12th GPIO pin on the controller board. By controlling the voltage at the 12th GPIO pin of the controller one can control the state of the LED.
Elint Labz (www.elintlabz.in)
Page 3 of 6
Product Manual: LED Plug
Elint Labz (www.elintlabz.in)
Page 4 of 6
Product Manual: LED Plug
State of D pin on the LED PLUG
LED plug response
LOW
Elint Labz (www.elintlabz.in)
Page 5 of 6
Product Manual: LED Plug
HIGH
In this example, we are going to blink an LED with 1 second delay that means LED turns ON for one second and turns OFF for another second.
// making 12th pin HIGH so that LED turns ON // wait for 1 second delay so that LED stays ON for 1 second // making 12th pin LOW so that LED turns OFF // wait for 1 second delay so that LED stays OFF for 1 second
Jun 5, 2017 - In this example, we are going to blink an LED with 1 second delay that means LED turns. ON for one second and turns OFF for another second. Example Codes. Code 1: Arduino void setup(). {. pinMode(12,OUTPUT); // define 12th GPIO pin as OUTPUT pin. } void loop(). {. digitalWrite(12,HIGH); // making ...
Product Manual: LED Plug. Introduction. This version of LED plug has an LED, SMD resistors and a transistor. In this plug. CTBC 547B transistor is used, It has a ...
Jun 19, 2017 - In this example, we are going to demonstrate the working of the Bi-color LED plug. Initially Red color LED blink once with the delay of one second and after that Green color LED blink once with the delay of one second and finally both.
Nov 27, 2017 - electronics & programmable development hardware more accessible. Elint Labz as a platform helps developers & young engineers from prototyping to product development. We provide open source hardware solutions and small quantity manufact
Nov 27, 2017 - TSOP, an IR receiver, outputs a constant HIGH signal when it is idle and as it receives data from the remote, it tends to invert the data. i.e when an IR LED of the remote is transmitting data onto the TSOP, every time the IR led goes
Index. 1. Introduction. 2. Specification. 3. Operatingâ âvoltage:â â5V. 3. Variants. 4 .... To activate the relay Plug the corresponding data pin on the controller board to ... Normally Open Contact (NO): âNO contact is also called 'make co
Cheap New Eu To China Plug Adapter Socket Plug Conve ... lectrical Outlet Free Shipping & Wholesale Price.pdf. Cheap New Eu To China Plug Adapter Socket ...
A Rotary potentiometer is a three terminal variable resistor with a rotating contact that forms an adjustable voltage divider. An adjustable potentiometer can open.
3. Variants. 4. Supported cables. 4. Details. 4. How to interface? 5. Example Codes. 7. Arduino. 7. Contributors. 8. Elint Labz (âwww.elintlabz.inâ). Page 1 of 7 .... Supported cables. â 4-4A. Details. Joystick plug is a analog input device to
manufacture development boards based on micro-controller & microprocessors, breakout boards ... the user's need and also this plug can be mounted anywhere using screws. ... to the Buzzer plug and 4 pin end of the cable is connected to the.
#define second_led 13 â//second LED is connected to 13th pin. #define first_datapin 10 â//D1 of slide switch is connected to. 10th pin. #define second_datapin ...
Nov 27, 2017 - manufacturing services using a design from manufacturing framework. ... large, predictable and precise change in electrical resistance when ...
Opendous inc. deeded this hardware design into the Public Domain. Opendous Inc. Title: UpconverterâiOOMHlâ13LOâSMS3926âCX2147. Size: A4 i Date: ...
output pin. } /* the loop function runs over and over again forever*/ voidâ âloopâ(). {. digitalWrite(Buzzer_pin, HIGH); â// activate the buzzer delay(â1000â);. â// wait for a second. digitalWrite(Buzzer_pin, LOW); â// deactivate the
Nov 27, 2017 - As in the name company (Elint Labz) â Electronic intelligence (âELINTâ) is intelligence gathered by the use of ... intelligent electronics & EL is committed to help achieve electronics literacy in India. No matter the vision ...
We defined all pixelsstrips in the screen as one big row (MAX config during startup). This all means every byte of pixel data controls 4 leds at a time. And MAX ...
AddConstants: xor round-dependent constants to the two first columns ..... cube testers: the best we could find within practical time complexity is ... 57 cycles/byte.
Dual LED plug has two 3mm LEDs with a current limiting resistors which can be used as an indicator in various projects. This PCB design enables you to bend ...
Created by the designer of the kingdom-building system ... LLC or other campaigns featuring themes like Gothic horror, the alien Lovecraftian mythos, epic.