LDT with Crimps Vibration Sensor/Switch Piezo Film Sensors High Sensativity AC Coupled Laminated Robust

The LDT0-028K is a flexible component comprising a 28 µm thick piezoelectric PVDF polymer film with screen-printed Ag-ink electrodes, laminated to a 0.125 mm polyester substrate, and fitted with two crimped contacts. As the piezo film is displaced from the mechanical neutral axis, bending creates very high strain within the piezopolymer and therefore high voltages are generated. When the assembly is deflected by direct contact, the device acts as a flexible "switch", and the generated output is sufficient to trigger MOSFET or CMOS stages directly. If the assembly is supported by its contacts and left to vibrate "in free space" (with the inertia of the clamped/free beam creating bending stress), the device will behave as an accelerometer or vibration sensor. Adding mass, or altering the free length of the element by clamping, can change the resonant frequency and sensitivity of the sensor to suit specific applications. Multi-axis response can be achieved by positioning the mass off center. The LDTM-028K is a vibration sensor where the sensing element comprises a cantilever beam loaded by an additional mass to offer high sensitivity at low frequencies.

dimensions

FEATURES • • • • • •

Solder Tab Connection Both No Mass & With Mass Version Withstands High Impact Operating Temperature: 0ºC to 85ºC Storage Temperature: -40ºC to 85 ºC Higher Temperature Version up to 125 ºC available on a Custom Basis

APPLICATIONS • • • • • •

Vibration Sensing in Washing Machine Low Power Wakeup Switch Low Cost Vibration Sensing Car Alarms Body Movement Security Systems

LDT0-028K Piezo Vibration Rev 1

www.meas-spec.com 1of 4

10/13/2008

LDT with Crimps Vibration Sensor/Switch examples of properties Four different experiments serve to illustrate the various properties of this simple but versatile component. Experiment #1 LDT0 as Vibration Sensor - with the crimped contacts pushed through a printed-circuit board, the LDT0 was soldered carefully in place to anchor the sensor. A charge amplifier was used to detect the output signal as vibration from a shaker table was applied (using a charge amplifier allows a very long measurement time constant and thus allows the "open-circuit" voltage response to be calculated). Small masses (approximately 0.26g increments) were then added to the tip of the sensor, and the measurement repeated. Results are shown in Table 1 and the overlaid plots in Fig. 1. Without adding mass, the LDT0 shows a resonance around 180 Hz. Adding mass to the tip reduces the resonance frequency and increases "baseline" sensitivity.

TABLE 1: LDT0 as Vibration Sensor (see Fig 1) Added Mass 0 1 2 3

Baseline Sensitivity 50 mV/g 200 mV/g 400 mV/g 800 mV/g

Sensitivity at Resonance 1.4 V/g 4 V/g 8 V/g 16 V/g

Resonant Frequency 180 Hz 90 Hz 60 Hz 40 Hz

+3 Db Frequency 90 Hz 45 Hz 30 Hz 20 Hz

Experiment #2 LDT0 as Flexible Switch - using a charge amplifier to obtain "open-circuit" voltage sensitivity, the output was measured for controlled tip deflections applied to the sensor (supported by its crimped contacts as described above). 2 mm deflection was sufficient to generate about 7 V. Voltages above 70V could be generated by bending the tip of the sensor through 90° (see Table 2, Fig. 2).

LDT0-028K Piezo Vibration Rev 1

www.meas-spec.com 2 of 4

10/13/2008

LDT with Crimps Vibration Sensor/Switch examples of Properties (continued) TABLE 2: LDT0 as Flexible Switch (see Fig 2) Tip Deflection

Charge Output

o/c Voltage Output

2 mm

3.4 nC

7V

5 mm

7.2 nC

15 V

10 mm

10 - 12 nC

20 - 25 V

max (90Ε)

> 30 nC

> 70 V

Experiment #3 LDT0 Electrical Frequency Response when the source capacitance of around 480 pF is connected to a resistive input load, a high-pass filter characteristic results. Using an electronic noise source to generate broad-band signals, the effect of various load resistances was measured and the -3 dB point of the R-C filter determined (see Table 3, Fig. 3).

TABLE 3: LDT0 Electrical Frequency Response (see Fig 3) (480 pF source capacitance)

LDT0-028K Piezo Vibration Rev 1

Load Resistance

-3 db Frequency

1 Megohm

330 Hz

10 Megohm

33 Hz

100 Megohm

3.3 Hz

www.meas-spec.com 3 of 4

10/13/2008

LDT with Crimps Vibration Sensor/Switch

Experiment #4 LDT0 Clamped at Different Lengths using simple clamping fixture, the vibration sensitivity was measured (as in (1) above) as the clamp was moved to allow different "free" lengths to vibrate. The sensor may be "tuned" to suit specific frequency response requirements (see Table 4, Fig. 4).

TABLE 4: LDT0 Clamped at Different Lengths (See Fig. 4) Length Beyond Clamp

Resonant Frequency

Settling Time (5 cyc)

20 mm (no clamp)

180 Hz

28 msec

16 mm

250 Hz

20 msec

11 mm

500 Hz

10 msec

7 mm

1000 Hz

5 msec

The information in this sheet has been carefully reviewed and is believed to be accurate; however, no responsibility is assumed for inaccuracies. Furthermore, this information does not convey to the purchaser of such devices any license under the patent rights to the manufacturer. Measurement Specialties, Inc. reserves the right to make changes without further notice to any product herein. Measurement Specialties, Inc. makes no warranty, representation or guarantee regarding the suitability of its product for any particular purpose, nor does Measurement Specialties, Inc. assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability, including without limitation consequential or incidental damages. Typical parameters can and do vary in different applications. All operating parameters must be validated for each customer application by customer’s technical experts. Measurement Specialties, Inc. does not convey any license under its patent rights nor the rights of others.

ordering information Description LDT0-028K LDTM-028K

Part Number 1002794-0 1005447-1

North America

Europe

Asia

Measurement Specialties, Inc. 1000 Lucas Way Hampton, VA 23666 Sales and Customer Service Tel: +1-800-745-8008 or +1-757-766-1500 Fax: +1-757-766-4297 Technical Support Email: [email protected]

MEAS Deutschland GmbH Hauert 13 44227 Dortmund Germany Sales and Customer Service Tel: +49 (0)231 9740 21 Technical Support Tel: +49 (0)6074 862822 Email: [email protected]

Measurement Specialties (China), Ltd. No. 26 Langshan Road Shenzhen High-Tech Park (North) Nanshan District Shenzhen, China 518107 Sales and Customer Service Tel: +86 755 3330 5088 Technical Support Email: [email protected]

LDT0-028K Piezo Vibration Rev 1

www.meas-spec.com 4 of 4

10/13/2008

LDT Series Datasheet

Oct 13, 2008 - The LDT0-028K is a flexible component comprising a 28 µm thick piezoelectric PVDF polymer film with screen-printed Ag-ink electrodes, laminated to a 0.125 mm polyester substrate, and fitted with two crimped contacts. As the piezo film is displaced from the mechanical neutral axis, bending creates very.

817KB Sizes 2 Downloads 297 Views

Recommend Documents

Datasheet
Jun 4, 2013 - Table 91. LQFP64 – 10 x 10 mm 64 pin low-profile quad flat package mechanical data. ..... to-pin, software and feature compatible with the STM32F2xx devices, allowing the user to ...... STMicroelectronics group of companies.

DS1307 Datasheet
plus 56 bytes of NV SRAM. ... 4. 8. 7. 6. 5. SDA l. 2. 3. 4. 8. 7. 6. 5. X1. X2. VBAT. GND. VCC. SQW/OUT. SCL. SDA .... Bit 6 of the hours register is defined as the.

W5500 Datasheet
Aug 1, 2013 - implement the Ethernet application just by adding the simple socket program. It's faster and easier way rather than using any other Embedded ...

DHT22 datasheet
*Extra components not needed. * Long transmission distance * Low power consumption. *4 pins packaged and fully interchangeable. 2.Description: Description: AM2303 output calibrated digital signal. It utilizes exclusive digital-signal-collecting-techn

Datasheet catalog
Dec 6, 1990 - For the DC characteristics see “74HC/HCT/HCU/HCMOS Logic Family Specifications”. Output capability: bus driver. ICC category: MSI. AC CHARACTERISTICS FOR 74HC. GND = 0 V; tr = tf = 6 ns; CL = 50 pF. SYMBOL. PARAMETER. Tamb (°C). UN

GC3355 DATASHEET
Nov 28, 2013 - advanced technology and highly integrated design, GC3355 target to provide multiple function and low cost solution in SHA256 application ...

Datasheet - GitHub
Dec 18, 2014 - Compliant with Android K and L ..... 9.49 SENSORHUB10_REG (37h) . .... DocID026899 Rev 7. 10. Embedded functions register mapping .

Datasheet RPR-220 - GitHub
Office automation equipment. FFeatures. 1) A plastic lens is used for high sensitivity. 2) A built-in visible light filter minimizes the influence of stray light.

datasheet 2FRM.pdf
Page 1 of 16. RE 28389, edition: 2013-05, Bosch Rexroth AG. 2-way flow control valve. Features. ▷ For subplate mounting. ▷ Porting pattern according to DIN ...

datasheet A4CSG.pdf
Axial piston variable pump. A4CSG Series 3x. RE 92105. Edition: 12.2016. Replaces: 07.2016. Type code for standard program 2. Hydraulic fluids 4. Shaft seal ...

BMP280 Datasheet - Adafruit Industries
May 5, 2015 - Please contact your regional Bosch Sensortec partner for more information about software ... 3.2 POWER MANAGEMENT. ...... The bus can.

datasheet 2FRM6A.pdf
With check valve;. with external closing. Type 2FRM 6 A...R... A B. P. A B. P. Page 3 of 16. datasheet 2FRM6A.pdf. datasheet 2FRM6A.pdf. Open. Extract.

Sliding Potentiometer datasheet - GitHub
Mechanical characteristicsi§§l

TMote Sky Datasheet
Nov 25, 2004 - Product Description. Tmote Sky is an ultra low power wireless module for use in sensor networks, monitoring applications, and rapid application prototyping. Tmote Sky leverages industry standards like USB and. IEEE 802.15.4 to interope

Datasheet TSOP22..
Low power consumption. Special Features. • Improved immunity against ambient light. • Suitable burst length ≥ 10 cycles/burst. Mechanical Data. Pinning: 1 = OUT, 2 = VS, 3 = GND. Parts Table. Block Diagram. Application Circuit. Part ... Junctio

TMote Sky Datasheet
Nov 25, 2004 - Figure 2 : Physical dimensions of Tmote Sky. All units are in inches unless otherwise noted. MIN. NOM. MAX. UNIT. Width. 1.24. 1.26. 1.29 in.Missing:

MQ-5 Datasheet
the MQ-5 on temperature and humidity. Ro: sensor resistance at 1000ppm of H2 in air at. 33%RH and 20 degree. Rs: sensor resistance at different temperatures.Missing:

datasheet DZD10D.pdf
Threaded pin with hexagon and protective cap. • Lockable rotary knob with scale. • Rotary knob with scale. – With pressure gauge connection. Content Page.

MiCS-6814 Datasheet - GitHub
Notes: 1. Sensing resistance in air R0 is measured under controlled ambient conditions, i.e. synthetic air at 23. ±5°C and 50 ± 10% RH for RED sensor and ...

Atmel AT42QT1070 Datasheet - Farnell
Jan 15, 2013 - Up to 10 mm glass; Up to 5 mm plastic (electrode size dependent) ..... or the design should be such that these lines are not switched ..... Top View .... CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL.

LMV358 Datasheet - GitHub
7.5 Electrical Characteristics: VCC+ = 2.7 V.. ... Implementation section, Power Supply Recommendations section, Layout ...... IPC-7525 may have alternate.

ITE Datasheet IT66121FN - GitHub
connectivity to myriad video displays such as LCD and CRT monitors, in addition to the .... In addition, advanced processing algorithms are employed ... (to host). Configuration. Register Blocks. PCLK. VSYNC. HSYNC. DE. D[23:0]. WS. I2S3/ ...

SW200D Datasheet - GitHub
SW-200D is two balls type single direction tilt sensitive trigger switch. 2. When the products tilt to the conductive terminal (silver-feet pin end A) and the tilt angle ...

LSM303D datasheet - STMicroelectronics
Nov 5, 2013 - interrupt signal for free-fall, motion detection and ...... value, rotating the sensor by 180 degrees (pointing to the sky) and ...... ST AS BEING INTENDED FOR “AUTOMOTIVE, AUTOMOTIVE SAFETY OR MEDICAL” INDUSTRY.