Heat Pump GSM Remote Control (FD25/35)

Control your heat pump from anywhere. Easy to use. Access Code -protection to prevent unauthorized remote access. Easy access to most frequently used controls. A total of 12 remote controlled heat pump related functions/parameters. Preserves settings during a power outage.

Heat Pump GSM Remote Control (FD25/35)

Installation 1. Insert the SIM card to cell phone SIM card

(Note: cell phone and SIM card not included with GSM Remote Controller)

2. Plug in the charger and hands-free cables to phone

hands-free cable charger cable

3. Turn on the phone and enter your SIM card PIN code

Power on + insert PIN

4. Turn on the Mini-GSM controller

Heat Pump GSM Remote Control (FD25/35)

Installation (continues...)

5. Make sure the front panel of the GSM remote controller points toward the indoor unit.

6. Now your setup should look like this and you are ready to configure cell phone!

Heat Pump GSM Remote Control (FD25/35)

Installation (Configuring cell phone)

There are a few settings to set right in cell phone (in this case we are using Nokia 3120) before we can start remote controlling. 1. Make sure you have general profile in use. If you are unsure what profile you have in use, hit power button once and choose ”General”. 2. Go to ”Menu -> Profiles -> General -> Personalise” and make sure everything there is set as follows: Incoming call alert: Ringing Ringing tone: Croak Ringing volume: Level 1 (= min) Vibrating alert: Off Message alert tone: Off Keypad tones: Level 3 (= max) Warning tones: Off Rhythmic backlight alert: Off Alert for: All calls 3. Make sure you have handsfree cable attached to cell phone. 4. Go to ”Menu -> Settings -> Enhancement settings -> Headset” and make sure everything there is set as follows: Default profile: Current Profile Automatic answer: On 5. Make a call to cell phone attached to a GSM remote controller. When cell phone automatically answers to your call press its button until volume is set to max level. 6. Ready!

Heat Pump GSM Remote Control (FD25/35)

How to use?

1. Make a call to Mini-GSM remote control attached cell phone. Can I change or disable Access Code? No.

2. Cell phone attached to Mini-GSM remote control will answer to your call automatically.

I unlocked the remote controller using Access Code. How long it takes before it reactivates? Reactivation happens about 2 min after last button press.

3. Enter your remote controller Access Code and start controlling your heat pump.

Basic functions cooling automatic power on

heating

power off temperature up by 1C° temperature 22C° temperature down by 1C° other control commands

Heat Pump GSM Remote Control (FD25/35)

Heat pump related commands

Fan #00 = #01 = #02 = #03 = #04 =

Auto Low Medium High Super High

Vane #10 = #11 = #12 = #13 = #14 = #15 = #16 =

Auto 1 2 3 4 5 Swing

Widevane #20 = #21 = #22 = #23 = #24 = #25 = Swing Area #30 = #31 = #32 = #33 =

Auto Left Right Release/Cancel

EconoCool #40 = Off #41 = On Clean #50 = Off #51 = On Plasma #60 = Off #61 = On i-see #70 = Off #71 = On Installation Position #80 = Left #81 = Center #82 = Right

Heat Pump GSM Remote Control (FD25/35)

GSM remote controller related commands

What is Autosend? Default function of Mini GSM remote controller is to send IR control message to heat pump right after every command or control.

This function can be turned off so that only * button sends control message to heat pump.

I entered a command that is not on these lists. What happens

#90 = Reset GSM remote controller with following settings: Operation mode: Heating Fan speed: Super High Vane: Swing WideVane: Swing Area: Auto EconoCool: Off Clean: Off Plasma: Off i-see: Off Power: Off Temperature: 22 Installation position: Center GSM remote controller sound: On Autosend: On (Note: Resetting the GSM remote controller does not send any control messages to the heat pump)

now? If you have Autosend on, currently active settings are sent to heat pump.

When recovering from power outage, does the GSM remote controller automatically send commands to the heat pump? No. FD25/35 heat pump has ”Auto restart function”.

#95 = Autosend OFF #96 = Autosend ON #97 = GSM remote controller sound OFF #98 = GSM remote controller sound SHORTER VERSION #99 = GSM remote controller sound ON+RESET

Heat Pump GSM Remote Control (FD25/35)

Remote control example (step by step)

- Power: On - Operation mode: Heating - Temperature: 24 (1-2-6-3-3) In this example Autosend is assumed to be on.

Press 1 (power: on). You will hear multiple beeps to indicate that IR control is sent to heat pump.

If you have set Autosend off in your GSM controller, then button sequence would be (1-2-6-3-3-*)

Press 2 (operation mode: heating). You will hear multiple beeps to indicate that IR control is sent to heat pump.

Press 6 (temperature: 22C). You will hear multiple beeps to indicate that IR control is sent to heat pump.

Press 3 (temperature: +1C). You will hear multiple beeps to indicate that IR control is sent to heat pump. Press 3 again to increase temperature by 1C. You will hear multiple beeps to indicate that IR control is sent to heat pump.

Heat Pump GSM Remote Control (FD25/35)

Remote control examples

- Power: On - Operation mode: Heating - Temperature: 24 (1-2-6-3-3)

- Power: On - Operation mode: Cooling - Temperature: 21 (1-8-6-9)

- Power: On - Operation mode: Automatic - Temperature: 22 (1-5-6)

- Power: Off (4)

- Fan: Super High (#-0-4)

- Reset GSM remote controller (#-9-0)

In this example Autosend is assumed to be on.

If you have set Autosend off in your GSM controller, then you need to add * to end of every button sequence.

Heat Pump GSM Remote Control (FD25/35)

GSM Remote Controller front & rear panel

Infra-red signal transmitter

Indicators

GSM hf cord

GSM button press Controller unlocked Power on

Power cord