1\

Roll No. ..........................

t

Total No. of Questions: 08]

(Total No. of Pages : 02

M. Tech. METHODS ENGINEERING AND ERGONOMICS ~:PE-523 .~: [E0460] (Note: Please fill subject code and paper ID on OMR)

Time: 03 Hours Instruction to C.andid~tes: 1) 2) Ql)

Maximum Marks: 100

Attempt any'Five questions. All questions carry equal marks.

(a) How are Industrial Engineering and productivity related?'Define the various types of productivity.

(b) . What is the differencebetweenmethod study and work measurement? List the various objectives C?fmethod study.

Q2) (a) Discuss the various principles of motion economy. (b) What is Time Study? How is a job selected for time study? Q3) (a) What is the role of ergonomics in industrial engineering? (b) Discuss the various factors which are considered for ergonomic design of controls. Q4) (a) What is Anthropometry? Explain the use of human anthropometry in workplace layout. (b) From the ergonomic design point of view, give recommendations for posture both for standing and slated at work. Q5) (a) Compare and contrast between static and dynamic muscular load. (b) Discuss the general steps in the measurement of mental work load. Q6) (a) Discuss the various methods by which vibrations can be reduced. (b) Discuss the various effects of heat on body and work performance.

J-4195/8129}

RT.O.

Q7) (a) What is meant by the term noise? Discuss the physiological effects of nOIse. (b) Discuss the difference between temporary and permanent threshold shift.

Q8) Write short notes on the following: (a) Measurement of physical work load. . (b) Wage incentive plans. [&][&][g] [&]

(-4195

2

Ii

GNDEC M.Tech PE December 2009 Methods Engineering ...

Page 1 of 60. Roll No. .......................... 1 \. t Total No. of Questions: 08] (Total No. of Pages : 02. M.Tech. METHODS ENGINEERING AND ERGONOMICS. ~:PE-523 .~: [E0460]. (Note: Please fill subject code and paper ID on OMR). Time: 03 Hours. Instruction to C.andid~tes: 1) Attempt any'Five questions. 2) All questions carry ...

820KB Sizes 0 Downloads 60 Views

Recommend Documents

GNDEC M.Tech PE December 2009 Welding Technology.pdf ...
Describe the solidification mechanism occurred in fusion. ofweldments? (b) Explain the effects of alloying of various elements on welding of carbon. alloy steel? Q2) Define welding arc? Explain the mechanism of arc initiation and itsmaintenance? Q3)

GNDEC M.Tech PE December 2009 Industrial Tribology.pdf ...
or its equivalent. Page 3 of 7. Whoops! There was a problem loading this page. GNDEC M.Tech PE December 2009 Industrial Tribology.pdf. GNDEC M.Tech PE December 2009 Industrial Tribology.pdf. Open. Extract. Open with. Sign In. Main menu. Displaying GN

GNDEC M.Tech PE 2009 Computer Aided Design & Manufacturing.pdf
Two stage computer. based test followed by. document verification. 1. Special Recruitment Drive (SRD) for PWDs. Allahabad. Degree from. recognized university. or its equivalent. Page 3 of 7. Whoops! There was a problem loading this page. Retrying...

GNDEC B.Tech CE 4th Year 2009 Irrigation Engineering-II.pdf ...
Q7) What is meant by the terms 'Flexibility', 'Proportionality', 's~tting' and. 'sensitivity' as applied to modules. Derive equation's for them and discuss. relation between these terms. Q8) Explain how will you determinethe following in design of a

GNDEC M.Tech CS Dec 2009 Software Engineering Methodologies ...
SOFTWARE ENGINEERING METHODOLOGIES. SUBJECT CODE :CS -514 (Elective - II) ... between incremental development and rapid application development. method. Q2) Define the terms: ... Page 2 of 2. Main menu. Displaying GNDEC M.Tech CS Dec 2009 Software En

GNDEC M.Tech EC 2009 Data Communication Networks.pdf ...
(b) Discuss the CSMA/CD MAC layer protocol in detail. Q5) (a) Differentiate between packet..switching, message switching and circuit. ~witching in detail. . . . (b) What are the advantages ofFDDI over a basic Token ring? Q6) (a) What are functions of

December 18, 2009 - Sites
Dec 18, 2009 - ALIX: Commercial building best buy on 2 corner .... Council table this item until the next budget meeting. ...... Tupperware Party Hosting.

GNDEC M.Tech PE Dec 2007 Metal Forming.pdf
Q7) (a) What is the function of support roll in rolling mill. ... effect of support roll on the torque. ... Displaying GNDEC M.Tech PE Dec 2007 Metal Forming.pdf.

December 2009 Newsletter.pdf
Hilda Novinger, New Mark Care Center. Dick Youngstrom, Clinton Care, Plattsburgh. Jim & Willa Phillips, Cedars of Liberty. Norma Schupp, Garden Village.

December-2009.pdf
on Islamist extrem- ism in British prisons. is based largely on ... Islamic TV stations from within prison (Eric. McGraw writes). ..... Page 3 of 60. December-2009.pdf.

GNDEC M.Tech CESE 2009 Sub Surface of Geophysical Exploration.pdf
Q1) (a) Discuss various factors that govern the sub soil exploration, bringing. out the guiding ... (b) How is the data from dynamic cone penetration test useful?

GNDEC B.Tech ME 1st Year 2009 Chemistry.pdf
B~Tech., (Sem. - 1st I 2nd) ... take tetra ethyl silane as a standard? Q8) (a) How is the ... Displaying GNDEC B.Tech ME 1st Year 2009 Chemistry.pdf. Page 1 of 2.

GNDEC B.Tech HM Sem 3 Dec 2009 Principles of Economics ...
Q7) Define monopoly. How price is determined under monopoly? ... GNDEC B.Tech HM Sem 3 Dec 2009 Principles of Economics & Management Paper 1.pdf.

GNDEC B.Tech ME Sem 4 2009 Applied Thermodynamics-II.pdf ...
j) What are the various assumptions made in practical cycle analysis in. gasturbines? M-858[1859] P.T.o.. Page 1 of ... Determine the power required and isentropic efficiency. The effectivejet exit velocity framjet ... Page 3 of 3. Main menu. Display

GNDEC B.Tech CSE 4th Year 2009 Formal Language & Automata ...
c) What do you understand by context sensitive grammars? d) What ... Displaying GNDEC B.Tech CSE 4th Year 2009 Formal Language & Automata Theory.pdf.

GNDEC MBA 2nd Year Dec 2009 Social Security & Labour Welfare ...
COMMUNICATION SERVICES: MESSENGERIAL (DHL) US Japan Middle East France. - Package. > Junior Box ..... Whoops! There was a problem loading this page. Retrying... GNDEC MBA 2nd Year Dec 2009 Social Security & Labour Welfare.pdf. GNDEC MBA 2nd Year Dec