Contents Removing the damaged print jet ................................................................................ 3 Installing the new print jet........................................................................................... 7 Levelling the print tips for CubeX Duo/Trio............................................................... 10 Setting Print Tip offsets ............................................................................................ 11 Fastening the print tip on a CubeX........................................................................... 12
2
What you will need Print jet assembly
2.5mm Hex driver
Pliers
3
Before beginning this process please remove all filament from the print jets and check that your print pad is level. For instructions on how to do this please refer to the CubeX users guide
Removing the damaged print jet 1. Turn off the CubeX printer and unplug it from the mains power. 2. Unplug the two white looms from the top of the damaged print jets sensor board,
3. Label the Print Jet motor looms with the corresponding print jet number and unplug them.
4
4. Remove the bolts holding the Feed Tube mount in place. The amount of bolt will vary depending on the amount of print jets your CubeX has.
A CubeX will have the bolts circled in red. A CubeX duo will have the two bolts circled in red and the bolt circled in green. A CubeX trio has the bolts circled in red, green and blue.
5. You should now be able to move the Feed Tube mount from the top of the print jets to expose the print jet mounting bolt.
5
6. Remove the mounting bolt. This can be very tight.
7. You should now be able to lift the print jet away from the Print Jet carriage plate.
6
Installing the new print jet 1. Check your Print Jet is assembled and that the print tip moves freely when pushed in and out of the drive. The Print tip moves freely for the levelling process. Once the levelling process has been completed the Print tip will be locked off.
If your Print Jet and print tip are not assembled together when you receive them, you can assemble them by inserting the locating end of the Print tip into the Print Jet as pictured below.
7
2. Place the Print Jet onto the Print Jet carriage plate as pictured, note the locating standoff and corresponding hole present on the Print Jet
3. Ensure that the wires from the Print tip are orientated to travel straight up to the Sensor board 4. Replace the M3 x 20 bolt into the hole as pictured and fasten. This must be tight.
8
5. Re attach the Feed Tube mount.
6. Plug the motor looms back into their corresponding motors.
7. Plug in the Print Jet sensor board looms.
9
Levelling the print tips for CubeX Duo/Trio If your CubeX only has a single print jet please see section ‘Fastening the print tip on a CubeX’ 1. Power on the CubeX printer 2. To clean the nozzles for levelling, put the CubeX printer into PJ-Control mode. Heat all of the print jets EXCEPT for the new one to 230° and clean of any plastic debris with pliers. Allow the Print Jets to cool down.
3. Put the CubeX printer into manual move mode.
4. Raise the print pad until it is approximately 5mm away from the print tips.
10
5. Slowly raise the print pad until it lifts the new print tip in line with the others. All three print tips should be touching the bed without putting any pressure on it.
6. Turn the CubeX printer off and unplug it from the mains power supply.
7. Using the 2.5mm hex driver, tighten the print jet holding bolt (pictured) to lock the print jet in place.
With the print tips levelled you can now turn on the CubeX printer and set the print tip offsets
Setting Print Tip offsets See the CubeX user guide for instructions on how to set your print tip offsets.
11
Fastening the print tip on a CubeX A CubeX with a single print jet does not have a second or third nozzle to reference the print tip level. Instead you have to use the CubeX wiping stick. 1. Power on the CubeX printer 2. Put the CubeX into manual move.
3. Raise the print pad until it is approximately 5mm away from the print tip.
4. Slowly raise the print pad until the print tip is touching it.
5. Continue raising the print pad until there is approximately 0.5mm between the print pad and the CubeX wiping stick.
12
6. Turn the CubeX printer off and unplug it from the mains power supply. 7. Using the 2.5mm hex driver, tighten the print jet holding bolt (pictured) to lock the print jet in place.
With the print tip fastened you can now turn on the CubeX printer and start printing.
the print tip level. Instead you have to use the CubeX wiping stick. 1. Power on the CubeX printer. 2. Put the CubeX into manual move. 3. Raise the print pad until ...
three print tips should be touching the bed without putting any pressure on it. 6. Turn the CubeX printer off and unplug it from the mains power supply. 7. Using the 2.5mm hex driver, tighten the print tip holding bolt (pictured) to lock the print ti
Unfasten the print tip holding bolt. The print tip and print jet are assembled by sliding the print tip into the print jet and twisting it (as pictured). To remove the print jet you will need to twist it and pull down, eventually you will find the co
15. Tightening the X belt. Use an M5 spanner to turn the loose X belt fastener until there is tension on the belt. Use the 3mm hex driver to fasten the X belt.
8 Mar 2006 - from the object B] Object-oriented programming is per formed by displaying objects connected by wirings that rep resent the ?ow of data, control or messages from one object to a second object. A coupling ofinput and output terminal so th
The research findings point out that there is significant worthiness to adopt computerised assessment technologies in higher education, including home exams.
indicating their experience with similar engagements. In addition, any relevant. Continuing Education Programs should be listed. 9.1.5.1 Substitutions for the ...
There was a problem previewing this document. Retrying... Download. Connect more apps... Try one of the apps below to open or edit this item. Main menu.
Retrying... Download. Connect more apps... Try one of the apps below to open or edit this item. JET AIRWAYS.pdf. JET AIRWAYS.pdf. Open. Extract. Open with.
Slowloud and bangin.Art ofwar pdf.45945425795 - Download JoannaJet Tsp.Torchwood s01e03 river. ... Their job is JoannaJet Tsp send out the blood to the body and lungs. JoannaJet. Tsp down the ... Whilethe ventricles pump blood out ofthe heart, theatr
How long will the procedure last and will I be under anesthesia? 4. Will I have dressings, bandages, or stitches after surgery? When should they be removed? 5.
ernment regulatory agencies could not make spectrum allocations in proportion ... cept is a system level idea which calls for replacing a single, high power trans-.
Removing the Jet Wipe. Run the bed to the bottom of the machine using manual move. Lift Jet wipe out of the machine. Removing the Case and floor panel.
Dui'ingrhe course discussions held on 0710512015 in the Chamberof ED/E(N) on NFIR's. pNM item No.l412015, the Official Side requested the Federation to provide details of specific. cases for taking necessary action to rectify the situation. ' ln this
Before beginning this process please ensure that all cartridges have been removed from the machine. Removing the Jet Wipe. Run the bed to the bottom of the machine using manual move. Lift Jet wipe out of the machine. Removing the Case and floor panel
elevator buckets, by creating the âoriginalâ JET range. Since 1989, the. JET elevator bucket has revolutionized the elevation sector by pro- viding a reliable, ...
In the GO read above orders have been issued to the effect that all Government employees and teachers who attain the age of 55 years during the course of the ...