Camur​ ​II​ ​Alarm

For​ ​monitoring​ ​and​ ​alarm​ ​triggering Description The​ ​Camur​ ​II​ ​Alarm​ ​node​ ​has​ ​four​ ​digital​ ​outputs​ ​that​ ​can​ ​be​ ​used​ ​to​ ​control​ ​alarm​ ​devices.​ ​Alarms​ ​may originate​ ​on​ ​different​ ​levels​ ​of​ ​the​ ​installation:​ ​by​ ​Project,​ ​Controller​ ​or​ ​Zone​ ​in​ ​Camur​ ​II​ ​software,​ ​or​ ​from alarm​ ​events​ ​in​ ​the​ ​event​ ​log.​ ​In​ ​Camur​ ​II​ ​software​ ​you​ ​select​ ​the​ ​alarm​ ​source​ ​and​ ​set​ ​the​ ​digital​ ​outputs on​ ​and​ ​off. Technical​ ​data Rated​ ​Load Rated​ ​Carry​ ​Current Max.​ ​switching​ ​voltage Max.​ ​switching​ ​current Max.​ ​switching​ ​power

0.5​ ​A​ ​at​ ​125​ ​VAC​ ​/​ ​1​ ​A​ ​at​ ​24​ ​VDC 2​ ​A 125​ ​VAC,​ ​60​ ​VDC 1​ ​A 62.5​ ​VA,​ ​30W

Power​ ​in 12-48​ ​V​ ​(9-38​ ​mA​ ​@​ ​24V) Power​ ​consumption No​ ​alarm 1​ ​alarm 2​ ​alarms 3​ ​alarms 9​ ​mA 17​ ​mA 24​ ​mA 31​ ​mA

4​ ​alarms 38​ ​mA

Dimensions​ ​(WxHxD) 70​ ​x​ ​82​ ​x​ ​34​ ​mm ​ ​-​ ​w/connectors​ ​and​ ​clip 92​ ​x​ ​90​ ​x​ ​40​ ​mm Weight​ ​w/connectors 130​ ​g Delivered​ ​with​ ​DIN-rail​ ​mounting​ ​clip Connectors Bus Via​ ​left​ ​and​ ​right​ ​side​ ​quick​ ​plug​ ​bus​ ​connector​ ​(must​ ​be​ ​ordered​ ​separately). (+,​ ​-​ ​,​ ​H​ ​,​ ​L)

HS​ ​export​ ​code:​ ​9031​ ​8090

Camur​ ​II​ ​Alarm,​ ​Rev​ ​1​ ​-​ ​May​ ​2015 Page​ ​1​ ​of​ ​2

Outputs Quick​ ​plug​ ​connector

​ ​C1

Relay​ ​channel​ ​1​ ​SPDT

NC1

Relay​ ​channel​ ​1​ ​SPDT

NO1

Relay​ ​channel​ ​1​ ​SPDT

C2

Relay​ ​channel​ ​2​ ​SPDT

NC2

Relay​ ​channel​ ​2​ ​SPDT

NO2

Relay​ ​channel​ ​2​ ​SPDT

C3

Relay​ ​channel​ ​3​ ​SPST

NO3

Relay​ ​channel​ ​3​ ​SPST

C4

Relay​ ​channel​ ​4​ ​SPST

NO4

Relay​ ​channel​ ​4​ ​SPST

C​ ​=​ ​Common,​ ​NC​ ​=​ ​Normally​ ​Closed,​ ​NO​ ​=​ ​Normally​ ​Open, SPDT​ ​=​ ​ ​Single​ ​Pole​ ​Double​ ​Throw Recording​ ​types The​ ​Alarm​ ​node​ ​supports​ ​recording​ ​types​ ​Monitor​ ​and​ ​Monitor​ ​Extended​ ​in​ ​Camur​ ​II​ ​software,​ ​but​ ​will​ ​not log​ ​to​ ​make​ ​reports.

HS​ ​export​ ​code:​ ​9031​ ​8090

Camur​ ​II​ ​Alarm,​ ​Rev​ ​1​ ​-​ ​May​ ​2015 Page​ ​2​ ​of​ ​2