2.0 DUAL EXTRUSION MODULE 2.5 ASSEMBLY MANUAL 雙擠出套件組裝說明手冊 Ver.2.5.0

Table of Contents English Version 03

Preface

04

A: Preparation

05

B: Remove Old Parts

16

C: Dual Etruder System I

22

D: Dual Etruder System II

29

E: Electronics

31

F: Glass Print Bed

33

G: Power Check

35

H: How to Use

53

Parts List

前言 Preface Congratulations on becoming an Atom owner! To ensure you have the best possible experience with your new Atom 3D Printer, please read the assembly instructions and precautions before you start, and keep in mind the following: ・ Assemble the machine according to the instructions and carefully read all of the assembly tips. ・ Children should always assemble Atom under close adult supervision. ・ Keep away from liquids, moisture, and open flames. ・ Keep objects out of the enclosure of the main control board and away from the build area when the machine is operating. ・ While the machine is operating DO NOT touch the nozzle directly. It may be extremely hot and cause serious injury. ・ Maintain at least 10cm between the machine body and walls or other objects. ・ When possible, use a seperate electrical outlet for the machine.

Troubleshooting For simple troubleshooting, or to download firmware or software, please visit: www.atom3dp.com/support For direct technical support, please contact your local Atom distributor, reach out to us on the Layer One Slack Community, or email [email protected]

A

Preparation

Tools

Tips

1

Assembly Tools 1. Vernier Caliper

4. ATOM Custom Wrench

3. Slotted 1.5mm

2. Round Head Hex Key Set

Screwdriver

5. Needle-nose Pliers & Diagonal Cutting Pliers

2. Gluestick

2

Lightly screw the M3 screws to the T-nut, but do not tighten. This allows you to position the T-nut into the 2020 extrusion.

3

After inserting the T-nut into the extrusion, tighten with the round hex key. The NYLOK® adhesive makes it easier to turn the T-nut to the correct position.

6. Measuring Tape

Printing and Maintenance Tools 1. Leather Knife

Each T-nut comes pre-applied with NYLOK® adhesive.

3. PTFE Lubricant

4. Lighter

glue stick

Preparation

Remove old parts

Dual extruder system I

Dual extruder system II

Electronics

Print bed

Power check

How to use

Dual Extrusion Upgrade Kit

P.4

B

Remove Old Parts

Pneumatic Connector

Extruder

(Φ4 x M6)

Parts

Motor Holder

X1

Remove and Keep

X1

Assembly Parts

Remove

Magnetic Rod

PTFE Tube 35.5mm

Top Corner Cover X1

X6 Cable Tube

Extruder Spring

X1

X1

Filament Junction Connector X1 M3 Nyloc Nut X1

X1

X1 M5 Washer

X1

X1

Glass Print Bed Aluminium Footing

(For Hotend)

Cable Housing

M3 30mm X1

Glass Holder X4

X4

2020 Aluminium Extrusion (with slot)

Aluminium Spacer 4.5mm

T-Nut

X1

X12

X1

M5 30mm X1

M3 4mm X2

M3 20mm

PTFE Tube 950mm

Hand Screw

X1

X1

M3 8mm

Plunger Base and Arm

M3 15mm

PTFE Tube 29.3mm

X6

(For Hotend)

X8

(with Pneumatic Connector,

X1

Bearing and M5 8mm)

X1

Shoulder Screw M3-12-3 X1

Stepper Motor (with Extruder Drive Gear and Headless Hex)

X1

Effector Tension Spring Φ3.9 x 58L

X1

Preparation

Remove old parts

Dual extruder system I

Dual extruder system II

Electronics

Print bed

Power check

How to use

Dual Extrusion Upgrade Kit

P.5

B

Remove Old Parts (Overview)

CAUTION

Some of the old parts should be removed in this step, but make sure that some parts should be KEPT FOR REUSE.

Preparation

Remove old parts

Dual extruder system I

Dual extruder system II

Electronics

Print bed

Power check

How to use

Dual Extrusion Upgrade Kit

P.6

B01

Remove Old Parts

M3 15mm

M3 15mm

M3 15mm

M3 15mm

Remove and Keep

M3 15mm X4 Glass Holder X4 Glass Print Bed X1 T-Nut X4

Preparation

Remove old parts

Dual extruder system I

Dual extruder system II

Electronics

Print bed

Power check

How to use

Dual Extrusion Upgrade Kit

P.7

B02

Remove Old Parts

Extruder Motor Wire

Move to the fifth socket.

Preparation

Remove old parts

Dual extruder system I

Dual extruder system II

Electronics

Print bed

Power check

How to use

Dual Extrusion Upgrade Kit

P.8

B03

Remove Old Parts

Remove and Keep

Remove

Top

M3 Nyloc Nut

Corner Cover

X1

X1

Cable Housing

M3 30mm

X1

X1

M3 8mm X6

M3 20mm

2020 Aluminium

Hand Screw

Extrusion (with slot)

X1

X1

T-Nut X6

8m

m

m

mm 0 3 3 M TT-

nu

nu

t

t

Cable Housing

T-nut

M3

Dual extruder system I

Top Corner Cover T-nut

T-nut

Remove old parts

M3 8mm

M3 8mm

ut N c o l M3 Ny

Preparation

Hand Screw

M3

8m

M3 20mm

M3

Dual extruder system II

Electronics

8m

M3 m

8m

T-nut

m

Print bed

Power check

How to use

Dual Extrusion Upgrade Kit

P.9

B04

Remove Old Parts

Remove

Remove

Preparation

Remove old parts

Dual extruder system I

Dual extruder system II

Electronics

Print bed

Power check

How to use

Dual Extrusion Upgrade Kit

P.10

B05

Remove Old Parts

Remove and Keep

Plunger Base and Arm

Keep the Effector Wire Assembly and the Motor Cable.

(with Pneumatic Connector, Bearing and M5 8mm)

X1 Stepper Motor

Stepper Motor

(with Extruder Drive Gear and Headless Hex)

X1 Extruder

M3 8mm

Spring

X2

X1

M3 15mm Shoulder Screw

X2

M3-12-3 X1 Remove

M3

15m

m T-nut Extruder

Extruder Motor Holder X1

Preparation

Remove old parts

M3 8mm

T-Nut M3 8mm

X2

e Scr

er d l u o h S -3 2 1 M3

Dual extruder system I

Motor Calbe

Mark this Motor Cable T-nut

as E1.

Motor Holder

w 15 3 M

Dual extruder system II

mm

Electronics

Extruder

Plunger Base and

Spring

Arm

Print bed

Power check

How to use

Dual Extrusion Upgrade Kit

P.11

B06

Remove Old Parts

Remove 拆除並保留 and Keep

Aluminium Footing X1 M5 Washer X4 Aluminium Spacer 4.5mm X1 M5 30mm X1

M5 Washer x2

M5 Washer x2 Aluminium Spacer 4.5mm Aluminium Footing M5 30mm

Use a Box to support the frame.

Preparation

Remove old parts

Dual extruder system I

Dual extruder system II

Electronics

Print bed

Power check

How to use

Dual Extrusion Upgrade Kit

P.12

B07

Remove Old Parts

Remove and Keep

PTFE Tube

M3 4mm

950mm

X2 Magnetic Rod X6 Effector Tension Spring

Φ3.9 x 58L

X1 Pneumatic Connector

(Φ4 x M6)

M3 4mm

X1 Cable Tube X1

M3 4mm

Remove

PTFE Tube 950mm X1

Counter Clockwise

Preparation

Remove old parts

Dual extruder system I

Dual extruder system II

Electronics

Print bed

Power check

How to use

Dual Extrusion Upgrade Kit

P.13

B08

Remove Old Parts

35

PT .5m FE m Tu be

29

Push

M3 4mm

PT .3m FE m Tu be

2

M3 4mm

1 Remove

Filament Junction Connector

Clockwise

Preparation

Remove old parts

Dual extruder system I

Dual extruder system II

Electronics

Print bed

Power check

How to use

Dual Extrusion Upgrade Kit

P.14

B09

Remove Old Parts

3

Hold the spring hooks in place.

2 Hook

Hook

4

Use a wrench to pull the spring around the M3 25mm screw.

1 Effector Tension Spring Φ3.9 x 58L

Preparation

Remove old parts

Dual extruder system I

Dual extruder system II

Electronics

Print bed

Power check

How to use

Dual Extrusion Upgrade Kit

P.15

C

Dual Extruder System I

Parts M3 8mm

M3 Nyloc Nut

X4

X2

M3 30mm

T-nut

X4

X4

1919 Extrusion Holder X1

Hand Screw

XH 2.54 2 Pin

M3 20mm

Top

X1

X1

Corner Cover X1

M3 Washer

XH 2.54 3 Pin

X4

X1

1919 Aluminium Extrusion X1

Preparation

Remove old parts

Dual extruder system I

Dual extruder system II

Slot Cover

Long Cable 1350mm

650mm

with Black XH 2.54 4 pin (E0)

X2

X1

Electronics

Print bed

Power check

How to use

Dual Extrusion Upgrade Kit

P.16

C

Dual Extrusion System I (Overview)

CAUTION

Carefully thread the wire harness with two hands and DO NOT pull it forcefully.

Preparation

Remove old parts

Dual extruder system I

Dual extruder system II

Electronics

Print bed

Power check

How to use

Dual Extrusion Upgrade Kit

P.17

C01

Preparation

Trim the Slot Covers by 18mm.

M3 8mm

M3 8mm

T-nut T-nut

632mm

M3 8mm M3 8mm

T-nut

T-nut

Preparation

Remove old parts

Dual extruder system I

Dual extruder system II

Electronics

Print bed

Power check

How to use

Dual Extrusion Upgrade Kit

P.18

C02

1919 Aluminium Extrusion Assembly I

nium i m u l A 1919 on i s u r t Ex

m m 0 3 M3

ash W 3 M

ash W 3 M

Moto

ire W r o t Effec ly b m e Ass er d u r t Ex 0) E ( e l ab C r o t Mo

er

±5 m 150m

er

The Extruder Motor Cable ±5 m m 170

E1 and the Effector Wire Assembly are from Step

ut N c o l y M3 N

B05.

E0

Preparation

r

er d u r t Ex 1) E ( e l Cab

Remove old parts

Dual extruder system I

Dual extruder system II

E1

Electronics

Print bed

Power check

How to use

Dual Extrusion Upgrade Kit

P.19

C03

1919 Aluminium Extrusion Assembly II

Slowly maneuver the 1919 Extrusion into place.

Hand Screw M3 20mm

Extruder Motor Cable (E0)

E0 E1

Extruder

Effector Wire Assembly

Motor Cable (E1) Effector Wire Assembly

Thread the Motor Cable E0 through the left slot.

E1

E0 Carefully pull to adjust the length.

DO NOT pull forcefully! Preparation

Remove old parts

Dual extruder system I

Dual extruder system II

Electronics

Print bed

Power check

How to use

Dual Extrusion Upgrade Kit

P.20

C04

1919 Aluminium Extrusion Assembly III

Correct

Wrong

Slot Cover

E1

Note the position of the hole and the direction of the terminals. The terminal with the spring plate is on the back

E0

side. Do not install it in reverse.

E0

Effector Wire Assembly

Extruder Motor Wire

Install the Slot Covers to cover the E0 and E1 wires.

Preparation

Remove old parts

Dual extruder system I

Dual extruder system II

Electronics

Print bed

Power check

How to use

Dual Extrusion Upgrade Kit

P.21

D

Dual Extruder System II

Parts

Extruder Motor Holder (Right)

M5 25mm

X1

(round head)

Stepper Motor

X2

(with Extruder Drive Gear and Headless Hex)

X1

Shoulder Screw M3-12-3 Extruder Motor

X1

Holder (Left)

Magnetic Rod

X1

X6

M3 15mm X4

Cable Tube X1

M3 25mm Tension Spring

X2

(Φ4 x 85L)

Pneumatic Connector

X2

(Φ4-M6)

M3 30mm

(One is from step B)

X2

X2

M5 8mm

PTFE 600mm

Plunger Base and Arm

X1

X2

(with Pneumatic Connector, Bearing and M5 8mm)

X1

Extruder Spring Φ8.5 x 32L (One is from step B)

M3 Nyloc Nut

M3 Washer

X2

X2

X4

Extruder Arm Extruder Base (Mirror)

Nylon Spacer (3mm) X2

X1 Handle

M5 Nyloc Nut

M5 Washer

X2

X2

X6

Nylon Spacer (7.5mm) X2

Dual Filament Junction (Pre-installed M2 8mm x4 and M3 6mm x2)

X1

Tray (with Axie and Bearing)

Bearing

Stepper Motor

X1

X1

X2

Preparation

Remove old parts

Dual extruder system I

Dual extruder system II

Electronics

Print bed

Power check

How to use

Extruder Drive Gear (Pre-installed M3 3mm grub)

X1

Dual Extrusion Upgrade Kit

P.22

D

Dual Extrusion System II (Overview)

CAUTION

After assembly, ensure that the filament can pass through the extruder, junction, and all connectors smoothly.

Preparation

Remove old parts

Dual extruder system I

Dual extruder system II

Electronics

Print bed

Power check

How to use

Dual Extrusion Upgrade Kit

P.23

D01

Dual Extrusion Assembly I

Handle Tension Spring (Black)

M5 25mm (BHSC) M5 Washer M3 25mm Tray Nylon Spacer (3 mm) M5 Washer Nylon Spacer (7.5 mm) M5 Washer Extruder Holder M5 Nyloc Nut

M3 N yloc N ut M 3 Wa sher M3 W asher

Preparation

Remove old parts

Dual extruder system I

Dual extruder system II

Electronics

Print bed

Power check

How to use

M3 3 0mm

Dual Extrusion Upgrade Kit

P.24

D02

Dual Extrusion Assembly I

Stepper Motor Extruder Motor Holder (Left)

Extruder Arm v2 (Mirror)

Stepper Motor

Extruder Spring

Affix the Headless Hex

(Φ8.5 x 32L)

screw to the flat surface Extruder Motor

Extruder Base v2 (Mirror)

of the motor axle.

Holder (Right)

The Stepper Motors’ connectors should face

Extruder Arm v2

downward.

re

w

Extruder Spring

-3

Extruder Base v2

12 in

g

3-

ar

Ge

Pneumatic Connector

ive

(Φ4-M6)

PLA

6.5mm

15

m

M3 4mm

3

Headless

M

M

3

15

m

m

m

Dr

Ex

tru

de

r

M

5

8m

m

Be

ar

M

Sh

ou

ld

er

Sc

(Φ8.5 x 32L)

Hex

Stepper Motor Extruder Drive Gear

Preparation

Remove old parts

Dual extruder system I

Dual extruder system II

Electronics

Print bed

Power check

How to use

Dual Extrusion Upgrade Kit

P.25

D03

Dual Extrusion Assembly II

Dual Filament Junction (Pre-installed M2 8mm x4 and M3 6mm x2)

3mm

The Filament Junction must be installed perpendicular to the Effector Cover.

Carefully adjust the position of the PTFE tubes while tightening both sides of the Junction together. Tighten

Tighten

Both sides of the Filament Junction need not be making contact so long as the PTFE tubes are tightly in place and the filament can pass through them. Side View

Front View

Preparation

Remove old parts

Dual extruder system I

Dual extruder system II

Electronics

Print bed

Power check

How to use

Dual Extrusion Upgrade Kit

P.26

D04

Dual Extrusion Assembly III

Stepper Motor

Stepper Motor

Cable E0

Cable E1

(Left)

(Right)

E0

E1

The E0 and E01 motor wires only TPFE 600mm

TPFE 600mm

(Left)

(Right)

fit the sockets one way.

Loop the PTFE tubes as illustrated before inserting them in the Pneumatic Connector.

Preparation

Remove old parts

Dual extruder system I

Dual extruder system II

Electronics

Print bed

Power check

How to use

Dual Extrusion Upgrade Kit

P.27

D02

Rod Assembly

3

Trim the length of the Cable Tube as needed.

Use the Cable Tube to collect all of the cables after

Ceramic Heating Plate

Back Fan

Side Fan

Side Fan

Optical Endstop

2

Thermal Sensor

connecting.

1

Preparation

Remove old parts

Dual extruder system I

Dual extruder system II

Electronics

Print bed

Power check

How to use

Dual Extrusion Upgrade Kit

P.28

E

E

Electronics

Electronics (Overview)

Parts Stepper Motor Driver IC A8825 X1

Extruder Motor E0

CAUTION

The wiring of the control board should EXACTLY match the illustrations. If any wires are misplaced, the printer will not work and may even be damaged. Be extra careful in confirming the polarity of positive and negative wires (red and black, green and orange). If these wires are connected in reverse, it may cause a short or even damage the control board! Do not hot plug/unplug any of the wires. Failure to comply will result in damage that will not be covered under warranty!

Preparation

Remove old parts

Dual extruder system I

Dual extruder system II

Electronics

Print bed

Power check

How to use

Dual Extrusion Upgrade Kit

P.29

E01

Electronics I

Extruder Motor E0

Insert the motor driver into the fifth socket as illsutrated.

Preparation

Remove old parts

Dual extruder system I

Dual extruder system II

Electronics

Print bed

Power check

How to use

Dual Extrusion Upgrade Kit

P.30

F

F

Glass Print Bed

Glass Print Bed (Overview)

Parts

Glass Print Bed X1

Glass Holder X4

M3 15mm X4 Aluminium Footing X1 M5 Washer X4 Aluminium Spacer 4.5mm X1 M5 30mm X1

CAUTION

Ensure that the glass print bed is 注意! securely fastened and that it does not 在此步驟務必確認有將玻璃平台鎖緊。確保 move when pushed from any direction. 平台用手推移時不會移動。如此一來在列印 Any looseness or free movement of the 時才不會因為平台移動而導致列印失準。 plate will result in printing inaccuracy.

Preparation

Remove old parts

Dual extruder system I

Dual extruder system II

Electronics

Print bed

Power check

How to use

Dual Extrusion Upgrade Kit

P.31

F01

Glass Print Bed

M3 15mm

Glass Print Bed

Glass Holder

T-nut

Insert the Glass Holders (pre-installed with M3 15mm and T-nuts) and Glass Print Bed into the extrusion, then tighten all of the screws

M5 Washer x2

M5 Washer x2 Aluminium Spacer 4.5mm Aluminium Footing M5 30mm Preparation

Remove old parts

Dual extruder system I

Dual extruder system II

Electronics

Print bed

Power check

How to use

Dual Extrusion Upgrade Kit

P.32

G

Power Check

1

3

Ensure that all of the following fans are operating when the machine is powerd on.

a. Back Fan

Ensure the Auto Home function is working properly:

b. 5015 Fan

Via the LCD menu

on Baseboard

“Prepare > Home” Ensure that all carriages return to the top of the axes.

2

Ensure that both side fans are working.

Via the LCD menu “Control > Temperture > Fan Speed > 255” then press the button and check for motion.

CAUTION

If any of these steps fail, please check the components in this order: 1 . Check that all of the wires are connected properly. 2 . Check for short circuits or broken/damaged wires. 3. Use a multimeter to check whether any of the components are damaged. If all else fails, please contact us at: [email protected]

Preparation

Remove old parts

Dual extruder system I

Dual extruder system II

Electronics

Print bed

Power check

How to use

Dual Extrusion Upgrade Kit

P.33

G

Power Check

4

5

Adjusting the auto-level optical endstop.

Ensure that the nozzle is cold by checking

Check the rotation direction of the extruder Drive Gears

Via the LCD menu

the temperature indicated

“Filaments > Load E0” Left extruder, clockwise

on the LCD before proceeding.

“ Filaments > Load E1” Right extruder, counter-clockwise

The indicator light on the auto-level optical endstop will only turn on when the endstop is not being blocked by the screw. Adjust the auto-level screw slowly until the indicator light turns off. When the nozzle is pressed lightly, the light should turn on.

Normal Position: Light Off

Detected Position: Light On

6

Preheat nozzle (and heated bed).

Via the LCD menu “Prepare > Preheat Preset 1” Ensure that the Nozzle (and heated bed) temperature is rising. If it heats up successfully, choose “Prepare > Cool Down” before proceeding to the next step.

Preparation

Remove old parts

Dual extruder system I

Dual extruder system II

Electronics

Print bed

Power check

How to use

Dual Extrusion Upgrade Kit

P.34

H

How to Use

Installing the ATOM Firmware

CAUTION

Join the Layer One Communityto discuss Atom and other Layer One products. Get

The ATOM 2.5 Control Board comes pre-installed with firmware. Please

support from fellow users, talk about your

update to the latest firmware before your first print. Check the firmware

latest creations, share your experiences,

version on our website and compare it to the firmware information displayed

and contribute to open source projects all

on the LCD.

in one, convenient place.

www.facebook.com/groups/atom3dp

Download the latest firmware version at:

Follow the steps on our website to run

www.atom3dp.com/en/support

download and run Arduino (1.0.6) to install the latest firmware.

www.atom3dp.com/en/support

Auto Level and setting Adjust Offset

It is recommended to Auto Level and reset the Z-Offset before the first use,

layerone.typeform.com/to/oLClGL

after moving the Glass Build Plate, or after replacing or repairing an effector.

1 Install ATOM Firmware

via the LCD menu: “Bed Leveling > Run Auto Level”

Auto Level & Setting Adjust Offset Change Filament

Auto Leveling

2

Setting Adjust Offset Place a sheet of copy paper onto the Glass Build Plate, then via the LCD

Test Printing

menu select, “Bed Leveling > Adjust Offset”

Print Settings

Use the Control Knob to adjust the height of the nozzle so that the paper slightly rubs against the nozzle when shifted.

Preparation

Remove old parts

Dual extruder system I

Dual extruder system II

Electronics

Print bed

Power check

How to use

Dual Extrusion Upgrade Kit

P.35

H

How to Use

3

Changing PLA Filament

Preheat the nozzle. CAUTION: NOZZLE IS VERY HOT! via the LCD menu:

1

Trim the Filament (to a clean and unbent segment) at

“Prepare > Preheat Preset 1”

an angle with diagonal cutting pliers to give filament a sharp tip. Note the sharp point of the filament

4

should be on outer curve

Loading the filament: WARNING: Remember to preheat before loading or



unloading filament. From the spool

Thread the filament as illustrated, then via the LCD menu:

Cut

filam

“Filaments > Load E0” (Left Extruder)

ent w ith t his a ngle

“Filaments > Load E1” (Right Extruder)

5

Unloading the filament: WARNING: Remember to preheat before loading or

2

unloading filament.

Pull the Filament Spool Holder Handle horizontally to mount the spool.

Thread th e filament to about t his point →

Thread the filament as illustrated, then via the LCD menu: “Filaments > Unload E0” (Left Extruder) “Filaments > Unload E1” (Right Extruder)

5

Storing filament: When unloading and storing a spool of filament, use the spool’s holes so as to prevent future jams.

7

Cooling down the nozzle: via the LCD menu: “Prepare > Cool Down”

Preparation

Remove old parts

Dual extruder system I

Dual extruder system II

Electronics

Print bed

Power check

How to use

Dual Extrusion Upgrade Kit

P.36

H

How to Use

4

Test Printing

1

Measuring the print. After printing, use calipers to measure the dimensions

Format the SD card.

of the part. The margin of error should be ±0.5mm.

Download the test files from: www.atom3dp.com/support

2

Prepare to test print: Preheat the nozzle before printing!

3

Printing Files: via the LCD menu:

35mm 300mm

“Print From SD > 300height.gcode” to print the test file.

Control Filaments Bed Leveling > Print From SD

Preparation

Remove old parts

35mm

Dual extruder system I

Dual extruder system II

Electronics

Print bed

Power check

How to use

Dual Extrusion Upgrade Kit

P.37

H

How to Use

Installing Slicer

1

To begin slicing and printing parts we recommend Cura, an open source slicing software with profiles for Atom. Download Cura and other supported slicers at www.atom3dp.com/support/#slicers

2

Download CURA Settings for ATOM 2.5 EX and drop into: “Cura > Contents > Resources > machine_profiles”

“Cura \ resources \ machine_profiles” Hello again! Are you ready to start leveraging your creativity?

3

Run CURA, then choose:

Your 3D printing experience is about to begin.

“Machine > Add New Machine > Other > Atom25EX”

Before printing, we recommend that you refer to our

t o start your print.

website’s support page. This site can help you go from the initial print, to maintenance, troubleshooting, and through to advanced techniques such as module development. Atom Team — 2016.12.15

Preparation

Remove old parts

Dual extruder system I

Dual extruder system II

Electronics

Print bed

Power check

How to use

Dual Extrusion Upgrade Kit

P.38

If the content of your package does not match, please take a picture and send it to [email protected]

Parts List PN CPST007-01 CPST008-01 SPMV006-01

CPSU022-01

P i c tu r e s

零件名稱

Parts Description

料架

Tray

內含保持器、軸承

with Axle and Bearing

Qty

2

SAMV001-03

SPHE011-01

料架手把

Handle

2

MR105ZZ SPSC001-M2-8-N

CPSU010-01

CPCN004-03

CPCN005-03

CPEL004-01

CPHE007-01

Tension Spring 4x85L

2

步進馬達 ( 長線 )

Stepper Motor

( 線長 1350mm / 另附

(Long Cable 1350mm

XH 2.54 4PIN 黑端子頭 )

With Black XH 2.54 4 pin)

鐵氟龍管 2x4x35.5mm

PTFE Tube 2x4x35.5mm

1

軸承 MR105ZZ

Bearings MR105ZZ

1

內六角螺絲 M2 8mm

M2 8mm Hex Screw

[NYLOK]

[NYLOK]

1

4

SPSC001-M3-4

內六角螺絲 M3 4mm

M3 4mm Hex Screw

2

SPSC001-M3-6

內六角螺絲 M3 6mm

M3 6mm Hex Screw

2

Plunger Base V2 (Mirror)

V2 含 M3 3mm 止付螺絲

(with M3 3mm Headless

/ 2x6 PTFE

Hex/ 2x6 PTFE)

SPSC001-M3-8

內六角螺絲 M3 8mm

M3 8mm Hex Screw

4

進料手臂 ( 反 )

Plunger Arm V2 (Mirror)

SPSC001-M3-10

內六角螺絲 M3 10mm

M3 10mm Hex Screw

2

V2 含 M3 3mm 止付螺絲

(with M3 3mm Headless

/ 2x6 PTFE

Hex/ 2x6 PTFE)

SPSC001-M3-15

內六角螺絲 M3 15mm

M3 15mm Hex Screw

4

馬達驅動晶片

Stepper Motor Driver

SPSC001-M3-25

內六角螺絲 M3 25mm

M3 25mm Hex Screw

2

A8825

A8825

SPSC001-M3-30

內六角螺絲 M3 30mm

M3 30mm Hex Screw

4

SPSC001-M5-8

內六角螺絲 M5 8mm

M5 8mm Hex Screw

1

SPSC004-M2

M2 螺母

M2 Nut

4

SPSC005-M3

M3 墊片

M3 Washer

8

SPSC005-M5

M5 墊片

M5 Washer

6

SPSC006-M3

M3 防鬆螺母

M3 Nyloc Nut

6

SPSC006-M5

M5 防鬆螺母

M5 Nyloc Nut

2

SPSC008-03

尼龍柱 Ø5.1xØ8x3mm

SPSC008-04

尼龍柱 Ø5.1xØ8x7.5mm

SPSC013-M3

T 型螺母

M3-10 T-Nut

-10-N

M3-10 [NYLOK]

with NYLOK

SPSC013-01

限位螺絲 M3-12-3

噴頭導流器 預鎖 M2 8mm & M3 6mm

CPSM008-01

1919 通管

CPSM011-01

2

進料機構底座 ( 反 )

噴頭連接環

CPSM010-01

Parts List

拉伸彈簧 4x85L

CPHE008-01

CPSM009-01

PTFE Tube 2x4x600mm

(The Parts List lists the exact number of parts and their quantities needed to install the upgrade. Your DIY Kit will contain spare parts.)

SPMV004CPST009-01

鐵氟龍管 2x4x600mm

1919 通管固定架

進料馬達架 ( 右 )

進料馬達架 ( 左 )

1

1

1

Hotend - Dual Filament Junction

1

with M2 8mm & M3 6mm

Filament Junction Connector

1

1919 Aluminium Extrusion

1

1919 Extrusion Holder

Extruder Motor Holder (Right)

Extruder Motor Holder (Left)

1

1

1

CPSU001-02

擠料彈簧 V2 8.5x32L

Extruder Spring v2 8.5x32L

1

CPSU002-02

不鏽鋼擠料輪 含止付螺絲

Extruder Drive Gear v2

1

with Headless Hex

SPSC014-M5-25

SPSU013-01

Nylon Spacer Ø5.1xØ8x3mm

Nylon Spacer Ø5.1xØ8x7.5mm

Shoulder Screw M3-12-3

內六角螺絲 ( 圓頭 )

M5 25mm Hex Screw

M5 25mm

(BHSC)

溝槽蓋 650mm

Slot Cover 650mm Black

2 2 4 1 2

2

Dual Extrusion Upgrade Kit

P.39

Atom 25 Dual Extrusion Upgrade.pdf

There was a problem previewing this document. Retrying... Download. Connect more apps... Try one of the apps below to open or edit this item. Atom 25 Dual ...

11MB Sizes 7 Downloads 179 Views

Recommend Documents

Atom 20 Dual Extrusion Upgrade.pdf
There was a problem previewing this document. Retrying... Download. Connect more apps... Try one of the apps below to open or edit this item. Atom 20 Dual ...

Dual-wavelength laser source for onboard atom ...
Oct 19, 2011 - We present a compact and stable dual-wavelength laser source for onboard atom interferometry with two .... of the two input powers, we can set the power ratio on ... self, meaning that our solution is a good alternative to.

Atom Chips - Jörg Schmiedmayer
Atom Chips are starting to realize a similar practical advance for quantum optical systems based on neutral atoms and photons. In micro electronics, electrons ...

atom mr drop.pdf
There was a problem previewing this document. Retrying... Download. Connect more apps... Try one of the apps below to open or edit this item. atom mr drop.

plastic extrusion process pdf
There was a problem previewing this document. Retrying... Download. Connect more apps... Try one of the apps below to open or edit this item. plastic extrusion process pdf. plastic extrusion process pdf. Open. Extract. Open with. Sign In. Main menu.

Dephasing due to atom-atom interaction in a ...
Sep 13, 2006 - Dephasing due to atom-atom interaction in a waveguide interferometer using a Bose-Einstein condensate. Munekazu Horikoshi and Ken'ichi Nakagawa. Institute for Laser Science and CREST, University of Electro-Communications, 1-5-1 Chofuga

History of Atom TC.pages
400 B.C. Democritus. • matter is composed of tiny, indestructible atoms. • Each type of matter is made of small pieces of the same substance (ie, Iron is made of iron,. Water is made of water, etc.) • atoms have different shapes, sizes, are in

The structure of Atom II.pdf
Melting Definition. Melting is the process where a solid changes to its liquid state at a certain. temperature (called the melting point) and pressure when it is ...

atom-c2000-microserver-r6-nnsrtp.pdf
Loading… Page 1. Whoops! There was a problem loading more pages. atom-c2000-microserver-r6-nnsrtp.pdf. atom-c2000-microserver-r6-nnsrtp.pdf. Open.

Build an Atom Post Lab.pdf
You start with your atom: 3 protons. 4 neutrons. 3 electrons. You want to change your atom's properties. Mark YES if a change will work, and mark NO if it will not work. A. Hydrogen, Helium, Lithium, Beryllium, Boron, Carbon are all different element

Models of the Atom ppt.pdf
There was a problem previewing this document. Retrying... Download. Connect more apps. ... Models of the Atom ppt.pdf. Models of the Atom ppt.pdf. Open.

Models of the Atom Notes.pdf
There was a problem previewing this document. Retrying... Download. Connect more apps... Try one of the apps below to open or edit this item. Models of the ...

Atom Models - Democritus, Dalton, Thompson ... - Chalkbored
To draw them you must know the # of protons, neutrons, and electrons (2,8,8,2 filling order). • Draw protons (p+), (n0) in circle (i.e. “nucleus”). • Draw electrons around in shells. Isotopes and Radioisotopes. • Atoms of the same element t

Build an Atom PhET Simulation.pdf
protons than electrons. 8. Develop a relationship (in the form of a single sentence or equation) that can predict the charge based on the number and. types of particle. 9. Play with the simulation to discover what affects the mass number of your atom

The structure of Atom I.pdf
randomly upwards until the whole agar turns blue. 3. Diffusion of solid is defined operationally as the random movement of particles to all directions. in a solid.

Sicilian-Stories-A-Dual-Language-Book-Dover-Dual-Language ...
There was a problem previewing this document. Retrying... Download. Connect more apps... Try one of the apps below to open or edit this item. Sicilian-Stories-A-Dual-Language-Book-Dover-Dual-Language-Italian.pdf. Sicilian-Stories-A-Dual-Language-Book