A BRIEF DISCUSSION ON ASME SECTION VIII DIVISIONS 1 AND 2 AND THE NEW DIVISION 3 K.T.Lau, Ph.D., P.Eng., 3rd Annual Pressure Industry Conference, Banff, Alberta, Canada, February 1999. Last Update - October, 2000

Section VIII Division 1

Section VIII Division 2

Section VIII Division 3

"Unfired" Pressure Vessel Rules < 1940

Alternative Rules 1968

Alternative Rules for High Pressure 1997

Normally up to 3000 psig

No limits either way, usually 600+ psig

No limit; Normally from 10,000 psig

Organization

General, Construction Type & Material U, UG, UW, UF, UB, UCS, UNF, UCI, UCL, UCD, UHT, ULT

General, Material, Design, Fabrication and others AG, AM, AD, AF, AR, AI, AT, AS

Similar to Division 2 KG, KM, KD, KF, KR, KE, KT, KS

Design Factor

Design Factor 3.5 on tensile (4* used previously) and other yield and temperature considerations

Design Factor of 3 on tensile (lower factor under reviewed) and other yield and temperature considerations

Yield based with reduction factor for yield to tensile ratio less than 0.7

Design Rules

Membrane - Maximum stress Generally Elastic analysis Very detailed design rules with Quality (joint efficiency) Factors. Little stress alaysis required; pure membrane without consideration of discontinuities controlling stress concentration to a safety factor of 3.5 or higher

Shell of Revolution - Max. shear stress Generally Elastic analysis Membrane + Bending. Fairly detailed design rules. In addition to the design rules, discontinuities, fatigue and other stress analysis considerations may be required unless exempted and guidance provided for in Appendix 4, 5 and 6

Maximum shear stress Elastic/Plastic Analyses and more. Some design rules provided; Fatigue analysis required; Fracture mechanics evaluation required unless proven leakbefore-burst, Residual stresses become significant and maybe positive factors (e.g. autofrettage)

Normally not required

Introduced and may be required

Experimental design verification but may be exempted

More restrictions on materials; impact required in general with similar rules as Division 1

Even more restrictive than Division 2 with different requirements.Fracture toughness testing requirement for fracture mechanics evaluation Crack tip opening displacement (CTOD) testing and establishment of KIc and/or JIc values

Published Pressure Limits

Experimental Stress Analysis

Material and Impact Testing

Few restrictions on materials; Impact required unless exempted; extensive exemptions under UG-20, UCS 66/67

NDE Requirements

NDE requirements may be exempted through increased design factor

Welding and fabrication

Page 1 of 2

Different types with butt welds and others

More stringent NDE requirements; Even more restrictive than Division 2; extensive use of RT as well as UT, MT and UT used for all butt welds, RT otherwise, PT. extensive use of PT and MT Extensive use/requirement of butt welds and full penetration welds including nonpressure attachment welds

Butt Welds and extensive use of other construction methods such as threaded, layered, wire-wound, interlocking stripwound and others

KTL - 3rd Annual Pressure Equipment Conference, 1999 Last Update - October, 2000

User

Manufacturer

Professional Engineer Certification Safety Relief Valve

User or designated agent to provide specifications (see U-2(a))

User's Design Specification with detailed design requirements (see AG-301.1) include AD 160 for fatigue evaluation

User’s Design Specification with more specific details (see KG-310) including contained fluid data, etc with useful operation life expected and others. Designer defined

Manufacturer to declare compliance in data report

Manufacturer's Design Report certifying design specification and code compliance in addition to data report

Same as Division 2

Normally not required

Professional Engineers' Certification of Same as Division 2 but the Professional User's Design Specification as well as Engineer shall be experienced in high Manufacturer's Design Report pressure vessel design and shall not sign Professional Engineer shall be experienced for both User and Manufacturer in pressure vessel design

UV Stamp

UV Stamp

UV3 Stamp

Code Stamp and Marking

U Stamp with Addition markings including W, P, B, RES; L, UB, DF; RT, HT

U2 Stamp with Additional marking including HT

U3 Stamp with additional marking denoting construction type; HT, PS, WL, M, F, W, UQT, WW, SW

Hydrostatic Test

1.3 (Was 1.5 before the use of the 3.5 Design Factor in the 1999 Addenda)

1.25

1.25 (may be exempted for autofrettaged vessels)

* In 1998, Code Cases 2278 and 2290 for ASME Section VIII Division 1 allowed for alternative maximum allowable design stresses based on a a factor of 3.5 under certain provisions instead of a factor of 4 used by the Code. These code cases were incorporated into the Code in 1999.

Common Features Jurisdiction may have requirements in addition to Code Mandatory Manufacturer's Quality Control System Implementation and Audit Requirements Code Stamp Authorization through ASME Accreditation and Authorization Authorized Inspection Agency in accordance with QAI Authorized Inspector with Jurisdictional approval and certification Manufacturer being held accountable for Code Stamp Application and full Code Compliance NDE Personnel to SNT-TC-1A Note: This brief comparative table is presented for discussion and does not represent the opinion of the ABSA, the ASME or the ASME Boiler and Pressure Vessel Code Committees. Readers are advised to consult with the ASME Code Section VIII Divisions 1, 2 & 3 for details

Page 2 of 2

KTL - 3rd Annual Pressure Equipment Conference, 1999 Last Update - October, 2000

ASME Section VIII - ABSA

analysis required; Fracture mechanics evaluation ... fracture mechanics evaluation. Crack tip ... Authorized Inspector with Jurisdictional approval and certification.

15KB Sizes 18 Downloads 217 Views

Recommend Documents

asme mechanisms committee
Subcommittee Chairs responsible for papers reviews for their mailing expenses. ... The committees involved are: Mechanisms; Design Automation; Flexible.

Section 0 Section 1 Section 2 Section 3 -
Bit 1 = 0, No optional section. Bit 1 = 1, Optional section follows. 00. Bits 2-8 ... Field. Units. Width. (bits). Scale Reference. Numeric value. Character value. End.

asme mechanisms committee
from Technology Transfer Tutorials or NDEC participation might be used for awards. ... Design Technical Conferences program this year. Design of Spatial.

asme mechanisms committee 1999-2000
payment (up until 7/17); payment can be made at the conference. It is hoped ... SpeakersM. McCarthy solicited suggestions from teleconference participants on.

asme mechanisms committee 1999-2000
Guest: L. Tsai. CALL TO ORDER ... duties of the Mechanisms Committee chair is a good idea. ***1997 ... conferences, for a status on conference preparations.

14786894245823029018e98.Workspot VIII 2016_GIT_JCSS_rev ...
14786894245823029018e98.Workspot VIII 2016_GIT_JCSS_rev.2_FINAL.pdf. 14786894245823029018e98.Workspot VIII 2016_GIT_JCSS_rev.2_FINAL.pdf.

Henry VIII
He gave in to excess in eating and drinking and became a huge, bloated figure. Henry VIII. Henry VII's eldest son was Arthur, Prince of Wales. He married Catherine of Aragon, but died shortly thereafter, leaving the throne to fall to his younger brot

asme mechanisms committee 1999-2000
CALL TO ORDER ... conference and to the Mechanisms Committee: H. Lipkin and L. Tsai, the chairs of the ... There was general agreement that putting.

IGTI Student Scholarship Program - ASME Community
who show promise for their future profession in the turbomachinery field. ... (Proof of awards and honors, memberships in honorary or professional societies ... Bursar's Office (or similar University Financial Department that handles ... within the m

VIII Drawing.pdf
Q.2 Draw a pictures of a hand & a leg also pencil shade. 10. or. Draw a pictures of any two ... VIII Drawing.pdf. VIII Drawing.pdf. Open. Extract. Open with. Sign In.

(Appeals)-VIII, Chennai date
Mar 21, 2014 - 6th floor, 121, M.G.Road,. Chennai-34. Vs. Mr. K.M. Vidyasagar,. Flat No.8, 2nd floor,. 'Sapthaswara'. 57, 1st Avenue, Ashok Nagar. Chennai-600 083. PAN:AADPV3326K. ( /Appellant) ... some of the payees are residing in Chennai and Banga

asme mechanisms committee 1999-2000
Department of Mechanical Engineering. McGill University ... John Beard. Mechanical Engineering and Engineering Mechanics Department. Michigan ... Engineering. Georgia Institute of Technology ... Engineering. University of Florida - Case.

ASME-B31-3.pdf
There was a problem previewing this document. Retrying... Download. Connect more apps... Try one of the apps below to open or edit this item. ASME-B31-3.pdf.

asme b30 9 pdf
Page 1 of 1. File: Asme b30 9 pdf. Download now. Click here if your download doesn't start automatically. Page 1 of 1. asme b30 9 pdf. asme b30 9 pdf. Open. Extract. Open with. Sign In. Main menu. Displaying asme b30 9 pdf. Page 1 of 1.