Aeon Labs Door/Window Sensor (Z-Wave Door/Window Sensor)

Aeon Labs Door/Window Sensor– Functions for Developers(software V3.01+) Objective: The Aeon Labs Door/Window Sensor is a routing binary sensor device based on Zwave routing slave libruray V4.51. Door/Window Sensor application lists the following supported command classes in the Node Information Frame: • COMMAND_CLASS_SENSOR_BINARY • COMMAND_CLASS_BATTERY • COMMAND_CLASS_WAKE_UP • COMMAND_CLASS_ALARM • COMMAND_CLASS_SENSOR_ALARM • COMMAND_CLASS_CONFIGURATION • COMMAND_CLASS_ASSOCIATION • COMMAND_CLASS_MANUFACTURER_SPECIFIC, • COMMAND_CLASS_VERSION If d/w sensor is included into a SIS or SUC z-wave network, it will be associated to SIS or SUC automatically. As soon as d/w sensor is removed from a z-wave network it will restore itself into factory Settings. Version 3.01 don’t support wake up interval set command. This command will be supported from Version 3.02 onward.

Interface: Event And Response:

Event

Response

tamper switch Clicked

Node Info Frame/Enter learn mode

tamper switch Held

Sensor Alarm report Alarm report

tamper switch Released

magnet switch open/close

tamper switch Triple pressed Power on

Sensor Alarm Report Alarm report Wake up Notification Sensor Binary Report(configurable) Battery report(configurable) Basic Set Command(configurable) Start/Stop 10 minutes wake up state.

Wake 10 minutes(configurable)

We can configure d/w sensor send or don’t send the configurable commands. The destination nodes of Basic set command are all associated nodes. If d/w sensor don’t have associated nodes, basic set command will not be sent. The destination nodes of Sensor Alarm Report, Alarm report, Sensor Binary Report Battery report are listed in the following table. Destination nodes

Priority

SIS OR SUC Node

High

First Associated Node

Middle

Broadcast

Low

It means if the network has SIS or SUC node, d/w sensor will send to SIS or SUC node; Else, if d/w sensor has Associated Node, it will send to first associated node .If d/w sensor doesn’t have Associated Node, it will send these command as broadcast. The destination node of Wake Up Notification are listed in the following table. Destination nodes The Node configured by Wake up Interval set command

Priority Supreme

SIS or SUC Node

High

First Associated Node

Middle

Broadcast

Low

LED Show

Status

LED

Wake up

Out of network: Blink In network: ON

Sleeping

OFF

Wake up time: D/W sensor will keep wake up for 8 seconds after it send wake up notification command. if it receive a command,it will keep wake up for 8 seconds to wait next command. Press tamper switch 3 times, then D/W sensor will wake 10 minutes. If configured,d/w sensor will wake 10 minutes too when power on. Only 3 ways can abort this status: l

Pressing tamper switch 3 times, sleep right now;

l

D/W sensor received “Wake up no more information CC”, sleep right now;

l

Received other command, wake 8 seconds to wait next command.

Using the Configuration Command Class: Configuration Set Command 7

6

5

4

3

2

1

Command Class = COMMAND_CLASS_CONFIGURATION Command = CONFIGURATION_SET

0

Parameter Number Default

Reserved

Size Configuration Value 1(MSB) Configuration Value 2

……… Configuration Value n(LSB)

1.Parameter Number(8 bit) Currently the following parameter numbers are defined: Description

Parameter Number

1

Toggle Sensor binary report value when Magnet switch open/close

2

Enable wake up 10 minutes when power on

3

Toggle Basic set value when Magnet switch open/close

121

Flag values for which Sensor is triggered

255

Reset to the default Configuration

reports to send

when the D/W

2.Default(1 bit) If the default bit is set to 1 the device is set to default factory setting and the configuration values is ignored. If the default bit is set to 0 then the configuration values is used. Refer to the table below with respect to default value for the relevant parameter number. Parameter Number

default factory setting

1

0

2

0

3

0

121

0x00000100

3.Reserved(4 bit)

Reserved bits must be set to zero. 4.Size(4 bit) The size field indicates the number of bytes that is used for the configration value. It's depended on the parameter Number. Refer to the table below with respect to size for the relevant parameter number. Parameter Number

Size

1

1

2

1

3

1

121

4

255

1

5. Configuration Value((variable): a. Parameter number equals 121 7

6

5

4

3

2

1

0

Reserved configuration Value 1(MSB)

Reserved

configuration Value 2

Basic Set

Reserved configuration Value 3

configuration Value 4(LSB)

l

Reserved

Reser ved

Reser ved

Reser ved

Sensor Binary

Reser ved

Reser ved

Reser ved

Batter y

Reserved bits or bytes must be set to zero. l

Basic Set (1 bit)

The Basic set flag signals that d/w sensor send(1) or don't send(0) Basic Set Command when magnet switch open/close . l

Sensor Binary (1 bit)

The Sensor Binary flag signals that d/w sensor send(1) or don't send(0) Sensor Binary Report when magnet switch open/close. l

Battery (1 bit)

The Battery flag signals that d/w sensor send(1) or don't send(0) battery Report when magnet switch open/close. b. Other Parameter Numbers Parameter Number

Configuration Value

Size

Description

(byte) 1

0x00

1

Open:FF,Close:00

0x01 2

Open:00,Close:FF

0x00

1

Disenable

0x01 3

Enable

0x00

1

Open:FF,Close:00

0x01

Open:00,Close:FF

Configuration Get Command 7

6

5

4

3

2

1

Command Class = COMMAND_CLASS_CONFIGURATION

Command = CONFIGURATION_GET Parameter Number

1. Parameter Number (8 bit)

Refer to description under the Configuration Set Command

0

Configuration Report Command 7

6

5

4

3

2

1

Command Class = COMMAND_CLASS_CONFIGURATION

Command = CONFIGURATION_GET Parameter Number

Reserved

size

Refer to description under the Configuration Set Command.

0

Aeon Labs Door/Window Sensor

It means if the network has SIS or SUC node, d/w sensor will send to SIS or SUC node; Else, if d/w sensor has Associated Node, it will send to first associated node .If d/w sensor doesn't have Associated Node, it will send these command as broadcast. The destination node of Wake Up Notification are listed in the following ...

223KB Sizes 17 Downloads 37 Views

Recommend Documents

ZONER: A ZONE-based Sensor Relocation Protocol for Mobile Sensor ...
sensor relocation protocol, ZONER, for mobile sensor networks on the basis of a restricted flooding .... The payload part contains communication data, the thus its format is application .... Figure 2(a) is a big picture about a discovery process.

Rotary sensor plug
A Rotary potentiometer is a three terminal variable resistor with a rotating contact that forms an adjustable voltage divider. An adjustable potentiometer can open.

Sensor placement in sensor and actuator networks
sor placement in wireless sensor and actuator networks (WSAN). One or more ..... This scheme has obvious advantage over the algorithms in [MXD+07] in mes-.

Swarm Based Sensor Deployment Optimization in Ad hoc Sensor ...
be resolved by any improvement in the onboard-sensor technology [1]. ... number of wireless sensor devices can be deployed in hostile areas without human.

Grove-Luminance Sensor PDF
F. 1. 0. 0 n. F. S. M. D. G ro ve. ;4. P. -2 .0. R. 1. C. 1. C. 2. IOUT. 1. VCC. 2. VCC. 3. NC. 4. U1. SIG. NC. VCC. GND. J1. P1 P2 P3 P4. VCC. VCC. GND. ASIGNAL.

Getting Started with Transact-SQL Labs - GitHub
Getting Started document for information about how to provision this. Challenge 1: Inserting Products. Each Adventure Works product is stored in the SalesLT.

Security Labs in OPNET IT Guru
-5-. L2.4. The scenario completed with all the links. 2. Network addresses definition: Click on ... To assign services, right click on a server, and then click on Edit.

Grove - loudness sensor pdf - GitHub
Dec 5, 2014 - Page 1. 2014/12/5 13:08:33 D:\Eagles\Grove - Loudness Sensor Eagle File\Grove-loudness sensor.sch (Sheet: 1/1)

piezoelectric sensor pdf
Page 1. Whoops! There was a problem loading more pages. piezoelectric sensor pdf. piezoelectric sensor pdf. Open. Extract. Open with. Sign In. Main menu.